User manual LANIER LP131N

[. . . ] Operating Instructions Hardware Guide 1 2 3 4 5 6 7 8 9 Guide to the Printer Installing Options Connecting the Printer Configuration Paper and Other Media Replacing Consumables and Maintenance Kit Cleaning the Printer Adjusting the Printer Troubleshooting 10 Removing Misfed Paper 11 Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information before using the machine. Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Do not copy or print any item for which reproduction is prohibited by law. [. . . ] · Sheets of A4 or 81/2 × 11 length or longer must be loaded one at a time. Additionally, since paper feeding and image quality may differ depending on paper thickness and width, check print results in advance using paper you intend to print on. Slide the side guides outward, and load paper until it stops with the print side up. AUB257S 95 5. Adjust the side guides to the paper width. AUB259S 5 · 45 g/m2 (12 lb. ) paper or paper of A4 or 81/2 × 11 or longer may not feed in properly unless it is cut at right angles. · If you load B5 or larger, slide out the bypass tray extension. AUB258S Specifying standard size paper for the bypass tray This describes how to load standard size paper into the bypass tray. Press the [Menu] key. AUB051S 96 Loading Paper The [Menu] screen appears. Press the [ ] or [ ] key to display [Paper Input], and then press the [ Enter] key. 3. Press the [ ] or [ ] key to display [Bypass Size], and then press the [ Enter] key. Press the [ ] or [ ] key to select the paper size you want to set, and then press the [ key. 5 5. · To load thick paper, OHP transparencies, or envelopes, make settings for thick paper, envelope, or OHP transparencies using both the control panel and printer driver. · The number of pages that can be loaded in the bypass tray differs depending on paper type. Make sure paper is not stacked above the paper guides inside the bypass tray. Specifying custom size paper for the bypass tray · When loading custom size or special paper, specify the paper size using both the control panel and printer driver. · Paper sizes between 139. 7 - 432 mm (5. 50 - 17. 00 in. ) in length and 64 - 216 mm (2. 52 - 8. 50 in. ) in width can be loaded in the bypass tray. However, the size range varies depending on a type of printer drivers. · Be sure to set a same size using both the control panel and the printer driver. · You cannot print on custom size paper with an application that does not support the custom size setting. Press the [ ] or [ ] key to display [Paper Input], and then press the [ Enter] key. 5 3. Press the [ ] or [ ] key to display [Bypass Size], and then press the [ 4. Press the [ ] or [ ] key to display [Custom Size], and then press the [ Enter] key. Press the [ ] or [ ] key to enter the horizontal value, and then press the [ By pressing the [ ] or [ ] key, the value increases or decreases by 0. 1 mm (0. 01 inch). By pressing and holding the [ ] or [ ] key, the value varies by 1 mm (0. 1 inch). You can set the horizontal value in the following range: 64 - 216 mm (2. 52 - 8. 50 inches). [. . . ] Paper Output Capacity: Standard 250 sheets (80 g/m2, 20 lb. ) Paper Input Capacity: Standard Paper Tray Bypass Tray *2 Optional Paper Feed Unit 500 sheets *1 100 sheets *1 500 sheets × 2 *1 189 11 11. Appendix Optional Envelop Feeder Unit *3 *1 Paper weight: 60 - 130 g/m2 (16 - 34 lb. ) 60 sheets *1 *2 You can load up to 10 envelopes (55 - 157 g/m2, 14 - 42 lb. ) at the same time. *3 To use the envelope feeder unit, the optional paper feed unit is required. The paper tray of the feed unit can be replaced with the envelope feeder unit. [. . . ]