User manual JENSEN VOYAGER AOM-7694

[. . . ] Seals(B) 1pc. 4pcs. 1pc. 1pc. Other Accessories CD Magazine(P/N 10CD56M) 5. °<This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning of the mechanism. ACC56M 10-DISC CD CHANGER 1pc. 1pc. 1pc. 2 3 WHERE TO INSTALL THE CHANGER A few of the many mounting possibilities are shown below. The following precautions must be considered when selecting the mounting location. [. . . ] The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. CAUTION: After setting the built-in anti-vibration springs, place the supplied Seals (B) over the holes. These seals are used to keep dust, which could cause a malfunction, out of the unit. HORZONTAL INSTALLATION Set the 4 anti-vibration springs to position H°± ° position H°± ° VERTICAL INSTALLATION Set the 4 anti-vibration springs to position V°± ° 45°£ NGLE INSTALLATION A Set the 4 anti-vibration springs to position° 45°£± ° position 45°£± ° ° position V°± ° 4 5 PROCEDURE FOR HORIZONTAL INSTALLATION £AAttach bracket (L) and bracket (R) to each side of the unit, using the hexagonal bolts with washer base (M5 x 10). Anti-vibration springs position PROCEDURE FOR VERTICAL INSTALLATION NOTE: If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 6), start with step 2. £A Set the 4 anti-vibration springs to position "v" £B Attach bracket (L) and bracket (R) to each side of the unit, using the hexagonal bolts with washer base (M5 x 10). NOTE: Use seals(A) to cover unused mounting holes on sides of unit. Bracket (L) NOTE: Use seals (A) to cover unused mounting holes on sides of unit. Bracket (R) Hexagonal bolt with washer base (M5 x 10) position "v" Bracket (L) Bracket (R) Hexagonal bolt with washer base (M5 x 10) £C Determine the mounting location, and drill four mounting holes. £D Mount the unit in place, using four self-tapping screws (T5 x 12). Use RTV(silicone sealer) on screw threads or around the holes to prevent moisture intrusion. Self-tapping screw (T5 x 12) £B Determine the mounting location, and drill four mounting holes. Never mount the unit near the fuel tank. Drill holes 4mm in diameter. £C Secure the unit in place, using four self-tapping screws(T5x12). Use RTV(sillicone sealer)on screw threads or around the holes to prevent moisture intrusion. Self-tapping screw (T5 x 12) Bracket (L) Bracket (L) Bracket (R) Drill holes 4mm in diameter. Unlike conventional records, the compact disc has no grooves to collect dust and microscopic debris, so gently wiping with a soft cloth should remove most particles. Small dust particles or light stains will have absolutely no effect on reproduction quality. 3. Never use such chemicals as record sprays, antistatic sprays or fluids, benzine or thinner to clean compact discs. Such chemicals could irreparably damage the disc's plastic surface. 4. Discs should be put back in their cases after use to avoid serious scratches that could cause the sound to skip. 5. Do not expose discs to direct sunlight, high humidity, or high temperatures for extended periods of time. 7. Do not write with any type of pen, pencil, or marker on the disc surface. 8. To minimize fingerprints and smudges on the signal surface, always try to hold the discs by their outer edge and center hole. 10 11 USE OF THE CD MAGAZINE Loading Disc Into The Magazine This CD Changer uses a specially-designed maga zine to hold up to 10 compact discs. To load discs into the magazine, grip the tab on the magazine tray into which you will be loading a disc and pull it out gently as shown in Figure 1. Insert a disc into the tray with the label side down (play surface facing up) as shown in Figure 2. 2 Removing Discs From The Magazine To remove a disc from the magazine, pull out the tray of the disc to be removed, lift out the disc, and push the tray back into the magazine. [. . . ] 1 Loading The Magazine Into The Changer Completely slide the door on the changer to the right as shown in Figure 4. Making sure the top of the magazine is facing upward, gently insert it into the unit until it clicks into place, as shown in Figure 5. Slide the door of the changer fully closed and the unit is ready for operation. Removing The Magazine From The Changer The magazine can be removed from the changer using one of two methods as outlined below in steps 1 and 2. [. . . ]