User manual JBSYSTEMS SM 1612 V 1.2
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JBSYSTEMS SM 1612. We hope that this JBSYSTEMS SM 1612 user guide will be useful to you.
Manual abstract: user guide JBSYSTEMS SM 1612V 1.2
Detailed instructions for use are in the User's Guide.
[. . . ] These 16 channels are divided over 2 pages with each 8 channels (faders): OVERRIDE BUTTON: When a chase is running, you can select 1 or more fixtures and control them independently from the chase running at that moment. RES10 13 FULL MESSAGE scene1 is active bank1 is active chase1 is active step 9 of a chase DMX-value the last fader used = 184 (0 255) Speed is set to 1minute and 34 seconds. MIDI/RECORD BUTTON: Used to record actions in memory or to set a MIDI channel. Used to change the readout of the channel DMX-values: you can change between real DMX-values (0 255) or values in percentage (0 100%) Also used as TAP-function in auto chase mode to set the chase speed: tap the button twice with a certain time interval. [. . . ] Press the scene button that corresponds to the scene you're editing. Note: Be sure to select the same scene in steps d and g, otherwise you may accidentally record over an existing scene. Enter program mode (Press and hold the "Program" button until its LED blinks) b. If you want to check the output, verify that the blackout LED is not lit, if it is, press it once to exit blackout mode. Press the Bank Up/Down buttons to select the bank you wish to copy the scene to. Enter program mode (Press and hold the "Program" button until its LED blinks) b. If you want to check the output, verify that the blackout LED is not lit, if it is, press it once to exit blackout mode. While holding the button, press the scene button that corresponds with the scene you wish to delete. When the programmed scene is deleted, all DMX channel values will be set to 0. The SCANMASTER 1612 only receives MIDI notes and you may have to transpose your keyboard to find the proper notes Enter program mode (Press and hold the "Program" button until its LED blinks) b. Check the blackout button and verify that the LED is not lit, if it is, press it once to exit blackout mode. You may control several fixtures together by pressing the button corresponding to the fixture(s) you wish to program. (In some rare cases, if necessary, you may select page B to control channels 9-16. Press the bank Up/Down button to choose the bank you want to store this scene into. There are a total of 30 banks you can select, you may store up to 8 scenes in each bank. Once all fixtures are programmed into the desired position for the scene, press the MIDI/Rec button. Switch the unit back on while you press and hold down the Program and Bank Down buttons at the same time. Note: Be aware that all your scenes will be lost, to be used with care!Enter program mode (Press and hold the "Program" button until its LED blinks) b. If you want to check the output, verify that the blackout LED is not lit, if it is, press it once to exit blackout mode. Press the Bank Up/Down buttons to select the bank you wish to copy to. Enter program mode (Press and hold the "Program" button until its LED blinks) b. [. . . ] Press the following buttons at the same time and hold down while you turn on the power: Scene2 button The display shows "RECEIVE" to indicate that the SM-1612 is ready to receive. Start sending file dump: On the Scanmaster showing "TRANSMIT" on its display, press the scene buttons 7 and 8 at the same time. At the end of the operation both units will automatically return to normal. Before you start using the unit that received the file dump, switch it off and on! [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JBSYSTEMS SM 1612
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JBSYSTEMS SM 1612 will begin.