User manual JBSYSTEMS MYSTERY LED II V 2.0

[. . . ] Condense sometimes prevents the unit from working at full performance or may even cause damages. If a foreign object enters the unit, immediately disconnect the mains power. Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. Don't cover any ventilation openings as this may result in overheating. [. . . ] electrical installation for 1 standalone unit: Just insert the mains cable. Remark1: You can connect a CA-8 remote controller to the unit if you want to have more control. refer to "how to operate the unit" to learn how to do this. Remark2: if there's no output, please make sure to set the unit in master mode (see next chapter) Electrical installation for two or more units in master/slave: Connect 2 to maximum 16 units together using good quality balanced microphone cables. Put the first unit of the chain in master mode, the rest must be set to slave mode (SL1 or SL2). Remark: You can connect a CA-8 remote controller to the master unit if you want to have more control over the master/slave operation Electrical installation in DMX-mode: The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to "daisy chain" your DMX controller and all the connected units with a good quality balanced cable. Both XLR-3pin and XLR-5pin connectors are used, however XLR-3pin is more popular because these cables are compatible with balanced audio cables. Mains output with IEC socket: you can use a special IEC power cable to connect this output with the mains input of the next MAGIC/MYSTERY LED II for easier linking. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook. Sound LED: blinks to the rhythm of the music while the unit is in audio mode 12. DOWN button: to go back in the menu and to lower the values shown on the display. To prevent strange behavior of the light effects, due to interferences, you must use a 90 to 120 terminator at the end of the chain. Each light effect in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode. Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The device should be installed out of reach of people and outside areas where persons may walk by or be seated. Before rigging make sure that the installation area can hold a minimum point load of 10times the device's weight. Always use a certified safety cable that can hold 12times the weight of the device when installing the unit. [. . . ] The interior of the device should be cleaned annually using a vacuum cleaner or air-jet. The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics. Mains Input: Power consumption: Fuse: Sound Control: DMX connections: DMX channels used: Lamp: Size: Weight: AC 230V, 50Hz 34 Watt 250V 6, 3A slow blow (20mm glass) Internal microphone 3pin XLR male / female 1 or 3 channels 2x 4-color 10Watt LEDs 296 x 271 x 140mm 4, 1kg Excellent programmes intégrés donnant lieu à de splendides light shows qui changent sans arrêt : Contrôle via DMX : fonctionnement aisé via un seul canal, ou au contraire, via 3 canaux pour un contrôle total ; Mode autonome : activation sonore via micro interne ; Mode maître/esclave : magnifiques shows synchronisés ; En option, une télécommande CA-8 est disponible. [. . . ]