User manual JBSYSTEMS LYNX II V1.0
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JBSYSTEMS LYNX II. We hope that this JBSYSTEMS LYNX II user guide will be useful to you.
Manual abstract: user guide JBSYSTEMS LYNX IIV1.0
Detailed instructions for use are in the User's Guide.
[. . . ] Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Always unplug the unit when it is not used for a longer time or when you start servicing. The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. Check that the available voltage is not higher than the one stated on the rear panel of the unit. [. . . ] The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!Don't cover any ventilation openings as this may result in overheating. The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. SENSITIVITY: Used to adjust the sensitivity of the micro when the unit is used in standalone or master/slave mode. MAINS FUSE: Always replace this fuse with a fuse that has the same characteristics!To select any of the functions, press the MENU button up to when the required one is shown on the display. After 8 seconds the display will automatically return to the main functions without any change. To go back to the functions without any change press the MENU button for about 2 seconds. Once the correct address shows on the display, press the ENTER button to save it. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again for about 2 seconds for about 2 seconds. Show Mode Used to choose the Show mode when used in standalone or master/slave mode. Tilt movement angle: 90° (60° above horizon; 30° below horizon. Tilt movement angle: 90° (vertically, front 75°; back 15°) Once the right mode shows on the display, press the ENTER button to save it. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again for about 2 seconds. REMOTE CONTROL INPUT: Used to connect a simple CA-8 hand controller while the unit is used in standalone or master/slave mode. Slave Mode Used to make the slave unit work in opposite to the master or to work in complete sync. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again for about 2 seconds. Sound Mode The unit works to rhythm of the beat when used in standalone or master/slave mode Press the MENU button until is shown on the display. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again for about 2 seconds. Blackout Mode Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMXsignal. No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone mode. [. . . ] In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be cleaned monthly. The interior of the device should be cleaned annually using a vacuum cleaner or air-jet. The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JBSYSTEMS LYNX II
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JBSYSTEMS LYNX II will begin.