User manual JBSYSTEMS LED MANAGER V 1.2
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JBSYSTEMS LED MANAGER. We hope that this JBSYSTEMS LED MANAGER user guide will be useful to you.
Manual abstract: user guide JBSYSTEMS LED MANAGERV 1.2
Detailed instructions for use are in the User's Guide.
[. . . ] Check the contents: Check that the carton contains the following items: LED-Manager Mains cable User manual Some important instructions: Before you start using this unit, please check if there's no transportation damage. Should there be any, do not use the device and consult your dealer first. Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. [. . . ] DMX OUTPUT: 3pin female XLR-connector used to connect the LED-Manager with the next DMX appliance in the chain or with another LED-Manager when used in master/slave mode. The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. How to connect the LED-projectors to the outputs of the unit: Important: Switch the LED-manager OFF before you install the LED-projectors!The maximum total load of the LED Manager is 300W, spread over 3 colors: each of the 3 colors has a max. Fix all projectors properly and daisy chain their in/output cables until you reach the maximum allowed load. Example: you can connect up to fifteen "1m LED STRIP" on each output cable (total = 30m!LED GROUND LIGHT): In this case we suggest to take a 1m extension cable (with special male/female 4pin connectors) and to cut the female connector. You will find 4 colored wires inside: White wire: This is the common wire (anode) Red wire: This the power for the red LEDs (max. 50W) Just connect these 4 wires to the corresponding 4 wires of the projector. (in most cases the colors of the wires match with the LED colors) Make sure not to exceed the maximum allowed load!Example: you can connect up to 50 "GROUND LIGHT" on each output cable (total = 100pcs!) Electrical installation in Master/slave-mode: You need to "daisy chain" the DMX in/outputs of 2 or more units with a good quality balanced cable (ex. The unit with a free DMX-input connector automatically becomes the master (master LED is lit), the other units are automatically switched as slaves (slave LED is lit). Electrical installation in Master/slave-mode with the LEDCON-01 remote: You need to "daisy chain" the DMX in/outputs of 1 or more units with the output of the LEDCON-01 remote using a good quality balanced cable (ex. Changing the internal batteries: VERY IMPORTANT: ONLY rechargeable batteries are allowed, do NOT use normal batteries! the LED Manager has an internal real-time 24H clock with 3 individual timers and battery backup. To use the battery backup feature you must install 3 optional AA-type NiMH rechargeable batteries. Once these batteries are installed they will be recharged automatically, no need to replace them anymore!) On the inside you will find a battery compartment, next to the fan. open it gently and install the 3 AAtype NiMH rechargeable batteries as indicated. Close the battery compartment Put the top cover back in place and fasten the 10 screws. During normal operation the display shows the current time of the internal 24H clock. [. . . ] So please refer to the chapter "Functions" to make yourself familiar with the various functions of the faders and buttons. Connect the LED Manager(s) with all other DMX-appliances in the DMX-chain. (DMX-LED on the LED Manager is lit) Switch your universal DMX-controller on and refer to the DMX chart below to control the connected LED managers: ) Switch the unit on and refer to the chapter "Functions" to make yourself familiar with the various functions of the faders and buttons. In this mode you can also set the clock and use the 3 on/off timers as described in the previous chapter. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JBSYSTEMS LED MANAGER
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JBSYSTEMS LED MANAGER will begin.