User manual JBSYSTEMS ICOLOR 4 V 1.1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JBSYSTEMS ICOLOR 4. We hope that this JBSYSTEMS ICOLOR 4 user guide will be useful to you.


JBSYSTEMS ICOLOR 4 V 1.1: Download the complete user guide (3785 Ko)

Manual abstract: user guide JBSYSTEMS ICOLOR 4V 1.1

Detailed instructions for use are in the User's Guide.

[. . . ] ⷠDon't cover any ventilation openings as this may result in overheating. ⷠPrevent use in dusty environments and clean the unit regularly. ⷠInexperienced persons should not operate this device. ⷠMake sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. [. . . ] The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual. ⷠKeep this booklet in a safe place for future consultation. Hanging bracket with 2 knobs · Important: Never look directly into the light source!Don't use the effect in the presence of persons suffering from epilepsy. In case of replacement of the lamp or maintenance, do not open the fixture within 10 minutes until the unit cools down after switching off. Use a screwdriver to unscrew the screw that closes the lamp compartment of the fixture. Hold the lamp firmly while pressing the new lamp gently in the socket. Check the label on the backside of the device or see the technical specifications in this manual to know which lamp should be used. Lamps with higher wattage generate temperatures the device was not designed for. If you touched the lamp, clean it with a cloth and a little denatured alcohol. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook. This input receives instructions from a DMX-controller or from another iCOLOR4 light effect when used in master/slave mode. DMX output: 3pin female XLR-connector used to connect the iCOLOR4 with the next unit in the DMX chain or with another iCOLOR4 when used in master/slave mode. In stand alone this red led blinks to the rhythm of the music, in DMX mode this led flashes when a DMX signal is detected. Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. ⷠMake sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. ⷠLocate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. ⷠThe device should be installed out of reach of people and outside areas where persons may walk by or be seated. ⷠBefore rigging make sure that the installation area can hold a minimum point load of 10times the device's weight. ⷠAlways use a certified safety cable that can hold 12times the weight of the device when installing the unit. [. . . ] ⷠHousings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any deformation. ⷠWhen an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced. ⷠThe mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected. ⷠIn order to protect the device from overheat the cooling fans (if any) and ventilation openings should be cleaned monthly. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JBSYSTEMS ICOLOR 4




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JBSYSTEMS ICOLOR 4 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.