Detailed instructions for use are in the User's Guide.
[. . . ] SET
5-1 5-2 5-3 5-4 5-5 5-6 5-7 Set dimmer-warm up 0% --- 6% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Set dimming or switch for each channel or all channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6 memory scenes --- be use for architectural lighting with CP-2A . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Set fader time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 The corresponding list of setting fader time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Set "square" or " 3 linear" dimming curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Maximum wattage limit setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Chapter 6. Specification of plug & wiring diagram
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
1
Lite-Puter
ISO 9001 CERTIFIED
The regulation of safe usage:
Setting for dimmer or switch on / off
Individual channel must be set dimming or switching function before the load switch ( circuit breaker) turns on. [. . . ] When the internal temperature is over 37, the fans start to work 1 minute and stop 1 minute in turn; over to 41, the fans turn continuously; over 75, all output will be stopped until the temperature goes down 70. SSR :40A/600V (75) Itrms=40A Itsm=350A / 60HZ , 300A / 50HZ (25) According with UL 81734
1-3
Speciafication
AC INPUT:100V-120V / 200V-240V, 45-63HZ 3 phases 4 wires or single phase 3 wires. LOAD: 20A MAX output per channel DMX signal ( 5 pin XLR) DMX512 / 1990 DMX signal input channel512 channels DMX signal input connectorXLR 5-pin Analog signal input valtage: 0-10V DC Analog signal input channel (D TYPE 15pin)12 channels Analog signal connectorD TYPE connector 15 PIN Dimension: 19" 4U482(L) x 176(H) x 260(D)mm Weight: 20. 5 KG
4
Lite-Puter
ISO 9001 CERTIFIED
Chapter 2.
2-1
Installation and function introduction
Installation
DX-1220 is composed of 12 sets "P-27" ( one channel module ) and 1 set of "DP-5" ( DMX interface ). The modular design is for easy to replace, repair and change update software fast. Front panel
P-27 PACK P-27 PACK P-27 PACK P-27 PACK P-27 PACK P-27 PACK P-27 PACK P-27 PACK P-27 PACK P-27 PACK P-27 PACK P-27 PACK
AC TRIG
AC TRIG
AC TRIG
AC TRIG
AC TRIG
AC TRIG
AC TRIG
AC TRIG
AC TRIG
AC TRIG
AC TRIG
AC TRIG
V1
V2
V3
DMX
FIRST CH.
CAN
SEL
SET
FNC MODE
0-10VDC ANALOG IN
PUSH
DMX OUT
DMX IN
ON TERMINATE
2-2
The main function of P-27
P-27 (One Channel Driver Module)
P-27 PACK
AC TRIG
5
Lite-Puter
ISO 9001 CERTIFIED
P-27
1. Ventilator Specifications:
AC input : 100 --- 240VAC AC output : 20A MAX Control input : 4 --- 12VDC Dimension : 30 * 176 * 192 mm ( W * H * D ) Weight : 0. 92 Kg
2-3
Introduction of DP-5
V1
V2
V3
DMX
CAN
SEL
SET FNC MODE
DMX OUT
DMX IN
( 6) Phase input indicators ( 7) DMX signal input indicator ( 8) LED display ( 9) wbutton (10) 5button (11) 4button (12) CANCEL button (13) SEL / select button (14) 6button (15) SET/ setting button (16) FUN / function button (17) MODE button (18) 5 PIN DMX "OUT" connector (19) 5 PIN DMX "IN" connector (20) 0-10VDC connector (21) Terminate switch (22) Unlock / lock knob: pull-unlock push-lock
6 Lite-Puter
ISO 9001 CERTIFIED
2- 4
Connection of DMX & ANALOG
The DP-5 is photo isolated from DMX signal input; data transfer is done by photo coupler. CAUTION: For using 5 pin XLR plug, do not connect PIN 1 to the housing of the plug.
DMX Connection
XLR 5pin
PIN 1: GND PIN 2: DATA PIN 3: DATA + PIN 4: NC PIN 5: NC
Analog Connection D-type 15pin
PIN 1: CH-1 PIN 2: CH-2 PIN 3: CH-3 PIN 12: CH-12 PIN 13: NC PIN 14: DC OUTPUT +12V / 100mA PIN 15: GND
Analog Connector
2-5
FOR 3 PHASE 4 WIRES E GND N N V1 V1(100A max) V2 V2(100A max) V2' V3 V3(100A max)
REAL PANEL
FOR 1 PHASE 3 WIRES E GND N N V1 V(100A max) V2 V2' V'(100A max) V3
N
12
E
N
11
N
10
E
N
9
N
8
E
N
7
N
6
E
N
5
N
4
E
N
3
N
2
E
N
1
E
E
N
N
LOAD CH12
E
LOAD CH11
LOAD CH10
E
LOAD CH9
LOAD CH8
E
LOAD CH7
LOAD CH6
E
LOAD CH5
LOAD CH4
E
LOAD CH3
LOAD CH2
E
LOAD CH1
V1 V2
V1 V2
V2'
V2'
V3
V3
23
24
25
(23) AC Main power input terminal 3 phases 4wires. 30A for each connecting point)
7 Lite-Puter
ISO 9001 CERTIFIED
Chapter 3.
MODE
Press "MODE" key , DX-1220 will offer 3 operation modes: "DMX" , "ANALOG" and "OFF" mode.
3-1
DMX mode
In the DMX mode, DX-1220 will accept DMX-512 dimming signal input also analog 0 --10VDC signal. Press "MODE" key to choose DMX mode, the LED will display the selected address of DMX as follows, and then press "SEL" key to confirm.
3-2
ANALOG mode
In the ANALOG mode, DX-1220 will only accept ANALOG signal input. Press "MODE" key to choose ANALOG mode, the LED will display as follows, and then press "SEL" to confirm.
3-3
OFF mode
In the OFF mode, DX-1220 will not accept any signal. Press "MODE" key to choose OFF mode, the LED will be display as follows, and then press "SEL" to confirm.
When system is turned on, memory resets to last selected mode prior to turning off. For example, if "OFF" mode was selected, then "OFF" mode continues when system is turned on.
8
Lite-Puter
ISO 9001 CERTIFIED
3-4
How to set the start address of channels
Operation:
Press "MODE" key to choice DMX mode, and then press the assist key to confirm the correct start address of DMX channels.
Assist key:
Press 4: Increase channel eg: Led display from d 0 0 1 to d 0 0 2. PressSEL: Select / Confirmation key.
PS: (1) In the DMX mode, total 512 channels can be set start address by users. (Each DX-1220 has 12 channels output. ) Eg. : If start address is set d 0 0 1 by users, and DX-1220 has DMX 1st channel ------ 12th channel . Eg. : If start address is set d 0 1 3 by users, and DX-1220 has DMX 13th channel ------ 24th channel . When a channel is set as non-dimming function, it will light when the percent of this channel light over 51%.
4-4
Display the Voltage (Only display the Voltage of V3)
Displays the current AC voltage and will change to 200 - 240VAC automatically if the AC input is 230VAC.
4-5
Display internal temperature
Internal temperature displayed to prevent from overheat and to control the operation of fans.
(1) To avoid inhaling dust. When the internal temperature is over 37, the fans start to work 1 minute and stop 1 minute in turn. (2) When the internal temperature is over 41, the fans turn continuously . (3) When the internal temperature is over 75, all output will be stopped until the temperature goes down 70. In this case, please check if the load are verload and the dimmer rack is stuffy.
Please refer to the regulations of safe usage in page 2.
13
Lite-Puter
ISO 9001 CERTIFIED
Chapter 5.
SET
Press "SET" key in turn and the LED will display 6 functions as follows:
(1) Set dimmer warm-up 0%---6. 0%. [. . . ] The output voltage value and the controlling value are in linear ratio, and it enables a wider control range in low brightness, so the professional lighting designers prefer to this. Indicator key : Press 5: Change dimming curve Press 6: Change dimming curve PressSEL: Select / Confirmation key
NOTEOriginal setting is C3.
100%
The human eyes are most sensitive to the light brightness range, which is under 25% of the 100% brightness, so the use of curve C3 enables a wider control range.
LIGHT OUTPUT
C2
C3
DIMMER TRAVEL %
19
100%
Lite-Puter
ISO 9001 CERTIFIED
5-7
Maximum Output Waltage Limit Setting :
Maximum waltage limit setting From 50%---FF% (Full lighting) : All channels 1: 1st channel 2: 2th channel 3: 3th channel 4: 4th channel 5: 5th channel 6: 6th channel 7: 7th channel 8: 8th channel 9: 9th channel A : 10th channel B : 11th channel C : 12th channel
Indicator key : Press 4: Increase channels. Press 5: Increase percentage of waltage Press 6: Decrease percentage of waltage. When a channel is set as non-dimming function, this channel doesn't have the pre-heat and output waltage llimit setting function. [. . . ]