User manual JBSYSTEMS DSP-6 V 1.1
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JBSYSTEMS DSP-6. We hope that this JBSYSTEMS DSP-6 user guide will be useful to you.
Manual abstract: user guide JBSYSTEMS DSP-6V 1.1
Detailed instructions for use are in the User's Guide.
[. . . ] ⷠDon't cover any ventilation openings as this may result in overheating. ⷠPrevent use in dusty environments and clean the unit regularly. ⷠInexperienced persons should not operate this device. ⷠAlways unplug the unit when it is not used for a longer time or before you start servicing. [. . . ] DMX OUTPUT: female XLR-connector used to connect the DSP6 to the next unit in the DMX chain. Attention: The analogue input only works when the "DMX fail" option is set to "Analog" and no DMX-signal is connected to the DSP6 (DMX led is off) In normal working condition the display shows the output states of the channels (see picture): The screen shows 6 channels. Above each channel there's a bar indicating the dimming level of that channel. The first digit shows the name of the channel that has been last modified. (in the picture the dimming value of channel 6 was the last modified) MENU Button: Used to access the different setup menus. ESC Button: Used to go one step back in the menu level or to leave the menu system. CHANNEL BUTTONS: The DSP6 can work without a controller for the input signals. This is a good option if you just need a certain output level on each channel over a long time (shops, exhibition booths, pubs etc. ) Just press and hold the channel button of the channel you want to edit. While you keep the channel button pressed you can use the "up/down" buttons to change the output level of that channel. CHANNEL INDICATORS: In addition to the LCD display these leds show the output condition of the channels. While connecting please pay attention to the "L" and "N" indications on the back panel. This unit may only be installed by qualified personal, following the rules for electrical installations in your country!After installation always put the metal covers back in place and make sure to use proper cable entry glands (see picture) to protect the wires from unwanted traction and friction. Since you have only 1 phase wire (L) you must make bridges between the L1/L2/L3 inputs and connect the phase wire to these inputs. Connect the loads to the output channels (2 connections, named "L" and "N") All connections named "N" are linked inside the DSP6. ⷠDon't forget to connect the earth connection properly!Please refer to the overview below to fully understand the menu structure of the DSP6: Since you have 3 phase wires you can connect these directly to the corresponding L1/L2/L3 inputs. Connect the loads to the output channels (2 connections, named "L" and "N") All connections named "N" are linked inside the DSP6. ⷠDon't forget to connect the earth connection properly! You can clearly see which buttons to push to select a certain function. In most cases the DSP6 is in normal working condition (display shows channel output condition). [. . . ] Setting the start address for the complete unit: · Press "menu" and "up/down" until the display shows "Dmx addr" · Press "up/down" until the display shows "Block" · Press "esc" to store the selected level and leave the menu. Press "menu" and "up/down" until the display shows "Curve". Press "up/down" until the display shows "All" · Press "menu" and "up/down" until the display shows "Dmx addr" Press "menu" again: the display shows one of the 2 options. Press "up/down" until the display shows "Single" Press "menu" to select this option: the display shows the channel number on the first row and the DMX address on the second row. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JBSYSTEMS DSP-6
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JBSYSTEMS DSP-6 will begin.