User manual JBSYSTEMS BT-575S V 1.1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JBSYSTEMS BT-575S. We hope that this JBSYSTEMS BT-575S user guide will be useful to you.


JBSYSTEMS BT-575S V 1.1: Download the complete user guide (2569 Ko)

Manual abstract: user guide JBSYSTEMS BT-575SV 1.1

Detailed instructions for use are in the User's Guide.

[. . . ] Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited. Dispose of the unit and used batteries in an environment friendly manner according to your country regulations. To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit. The minimum distance between light-output and the illuminated surface must be more than 1 meters. [. . . ] The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. never unscrew the screws of the rotating gobo as the ball bearing will be opened. Open the plastic top cover (4screws) Locate the gobo wheel and remove the fixation ring of the gobo you want to change with an appropriate tool. Press the fixation-ring together and insert it in the front of the gobo. BUTTONS MENU DOWN UP ENTER To To To To select the programming functions go backward in the selected functions go forward in the selected functions confirm the selected functions On On On Flashing DMX input present Master mode Slave mode Sound activation Show Mode Used to choose the Show mode when used in standalone or master/slave mode. Once the right mode shows on the display, press the ENTER button to save it. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. REMOTE CONTROL INPUT: Used to connect a simple CA-8 hand controller while the unit is used in standalone or master/slave mode. SENSITIVITY: Used to adjust the sensitivity of the micro when the unit is used in standalone or master/slave mode. MAIN MENU: To select any of the pre-set functions, press the MENU button up to when the required one is shown on the display. After 8 seconds the display will automatically return to the main functions without any change. Once the correct address shows on the display, press the ENTER button to save it. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. Once the mode is selected, press the ENTER button to setup ( or automatically return to the main functions without any change after 8 seconds. ) To go back to the functions without any change press the MENU button again. Show 3 mode - Fixture is placed on a podium, in front of the audience The spot is always projecting to the audience's direction; i. Tilt movement angle: 90° ( 60° above horizon; 30° below horizon. Tilt movement angle: 90° ( vertically, front 75°; back 15° ) Slave Mode Used to make the slave unit work in opposite to the master or to work in complete sync. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. Blackout Mode Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMXsignal. No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone mode. [. . . ] After that the unit will be ready to receive DMX signal or run the built-in programs. YOU CAN OPERATE THE UNIT IN FOUR WAYS: o By master/slave built-in preprogram function o By CA-8 easy controller o By universal DMX controller ( 8 & 16 channel DMX mode ) o By iLead controller ( The BT575S must be switched to 8 channel DMX mode ) BY MASTER/SLAVE BUILT-IN PREPROGRAM FUNCTION: Select this function when you want an instant show. By linking the units in master/slave connection, the first unit will control the other units to give an automatic, sound activated, synchronized light show. Its DMX input will have nothing plugged into it, and its master-LED will be constantly on and sound-LED will flash to the music. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JBSYSTEMS BT-575S




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JBSYSTEMS BT-575S will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.