User manual INTEGRA DTR-80.2

[. . . ] AV Receiver DTR-80. 2 DTR-70. 2 Instruction Manual Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] With the A/V Sync setting, you can correct this by applying a delay to the audio signal. If HDMI Lip Sync is enabled ( 67) and your TV or display supports HDMI Lip Sync, the displayed delay time will be the summation of the A/V Sync delay time and the HDMI Lip Sync delay time. The HDMI Lip Sync delay time is displayed underneath in parentheses. Note · A/V Sync is disabled when the Direct listening mode is used with an analog input source. · "A/V Sync" is not operable when the input selector is set to "NET/USB". A N ![ BC OP @# ] Shift +10 D E QR $% ; ' Space F S ^ , G T & . H U I V ( J W ) K X _ L Y M Z ~ / Back Space CLR OK All Erase Shift Shift*1: Switches the displayed character. (Left)/ (Right): Selected when the cursor is moved within the Name input area. Back Space*2: "Back Space" moves the cursor backward one character space. In addition, "Back Space" deletes the character to the left of the cursor. OK: Selects when the entry is complete. Tip *1 *2 Name Edit You can enter a custom name for each individual input selector (excluding Tuner) and radio preset for easy identification. Name You can also be performed on the remote controller by using +10. Press CLR on the remote controller, you can delete all characters in the input. To correct a character: 1 2 3 Note Use / / / to select " "(Left) or " "(Right), and then press Enter. Press Enter several times to select the incorrect character (The cursor moves one letter each time Enter is pressed). Use / / / to select the correct character, and then press Enter. 1 2 Use / / / to select a character, and then press Enter. When you've finished, to store a name, be sure to use / / / to select "OK", and then press Enter. Otherwise it will not be saved. · To name a radio preset, use Tuner to select AM or FM, and then select the preset ( 33). · (North American models) You cannot enter a custom name for SIRIUS radio presets. · "Name Edit" is not operable when the input selector is set to "NET/USB". To restore a custom name to the default, erase the custom name by entering an empty white space for each letter. En 62 Picture Adjust Using "Picture Adjust", you can adjust the picture quality and reduce any noise appearing on the screen. If video signal delay occurs during playback on a video component (i. e. game console), select the corresponding input source and set the "Game Mode" setting to "On". The delay will decrease but in return the picture quality will become poor. 4:3: Picture Mode*1 Custom: All settings can be performed manually. With "Picture Mode", you can change the following settings to be suitable for the movie or game screen by one operation; "Film Mode", "Edge Enhancement", "Mosquito NR", "Random NR", "Block NR", "Resolution", "Brightness", "Contrast", "Hue", "Saturation", "Gamma", "Red Brightness", "Red Contrast", "Green Brightness", "Green Contrast", "Blue Brightness", "Blue Contrast". [. . . ] · Stop playback of content from Internet Radio, iPod, USB or Servers, etc. How to turn off RIHD 8 9 10 11 1 2 3 1 2 In the Main menu select "Hardware Setup". Set "HDMI Control(RIHD)" to "Off". 12 13 14 Update procedure Connect a USB storage device to your PC. The file name is as follows: ONKAVR0001_*******. zip Unzip the downloaded file. [. . . ]