User manual INTEGRA DTR-40.2

[. . . ] AV Receiver DTR-40. 2 Instruction Manual Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] Input Channel Left + Right: Both the left and right channels are output. Left / Right: Mono audio is output by the front left and right speakers. This setting determines which speakers output mono audio when the Mono listening mode is selected. Note · If the "Center" setting is set to "None" ( 51), this setting is fixed at "Left / Right". En 54 Dolby EX This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD only. Auto: If the source signal contains a Dolby EX flag, the Dolby EX or THX Surround EX listening mode is used. Manual: You can select any available listening mode. Note · If the "Surr Back" setting is set to "None" ( 51), this setting cannot be selected. · If the "Front High" or "Front Wide" setting is enabled ( 51), this setting is fixed at "Manual". LFE Level Dolby Digital*1, DTS*2, Multich PCM, Dolby TrueHD, DTS-HD Master Audio, DSD*3 ­ dB, ­20dB, ­10dB, or 0dB With these settings, you can set the level of the LFE (Low Frequency Effects) channel individually for each input sources. If you find that low-frequency effects are too loud when using one of these sources, change the setting to ­20 dB or ­ dB. *1 *2 *3 Dolby Digital and Dolby Digital Plus sources. DSD (Super Audio CD) sources. Source Setup Items can be set individually for each input selector. Preparation Press the input selector buttons to select an input source. Main menu Source Setup DTS Neo:6 Music Center Image 0 to 2 to 5 The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. Sound is spread in left and right (the outside) so that the set value is made big. Please adjust by liking. Audyssey When Audyssey MultEQ® Room Correction and Speaker Setup is complete, the "Equalizer" ( 52) will be set to "Audyssey" and the "Dynamic EQ" will be set to "On". With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels. Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. It does so by selecting the correct frequency response and surround volume levels moment-by-moment so that the content sounds the way it was created at any volume level -- not just at reference level. Note · If Direct listening mode is selected, this setting cannot be selected. Audyssey DSXTM Soundstage ­3dB to Reference to +3dB With this setting, you can adjust the soundstage when using Audyssey DSXTM. Note · If the "Center" setting is set to "None", or both "Front High" and "Front Wide" settings are set to "None" ( 51), this setting cannot be selected. Theater-Dimensional Listening Angle Wide: Select if the listening angle is 40 degrees. With this setting, you can optimize the Theater-Dimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings. Front left speaker Front right speaker 20°/40° En 55 Reference Level Audyssey Dynamic EQ® Reference Level Offset 0dB: It should be used when listening to movies. 5dB: Select this setting for content that has a very wide dynamic range, such as classical music. 10dB: Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference. [. . . ] · Operation of the player/recorder is possible with the remote controller supplied with the AV receiver. * Not all functions may operate depending on the model. En 101 How to connect and setup 1 3 Confirm the connecting and setting. Connect the HDMI OUT MAIN jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note · When you use the audio return channel (ARC) function with TV an HDMI (Audio Return Channel) capable TV, this connection is not required ( 62). Confirm the settings. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation. [. . . ]