User manual INDESIT KN1G20S(W)/I

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual INDESIT KN1G20S(W)/I. We hope that this INDESIT KN1G20S(W)/I user guide will be useful to you.


INDESIT KN1G20S(W)/I : Download the complete user guide (2288 Ko)

Manual abstract: user guide INDESIT KN1G20S(W)/I

Detailed instructions for use are in the User's Guide.

[. . . ] If the cooker is installed underneath a wall cabinet, there must be a minimum distance of 420 mm between this cabinet and the top of the hob. This distance should be increased to 700 mm if the wall cabinets are flammable (see figure). Do not position blinds behind the cooker or less than 200 mm away from its sides. Any hoods must be installed according to the instructions listed in the relevant operating manual. [. . . ] Unscrew the nozzle using a special nozzle socket spanner (see figure) or with a 7 mm socket spanner, and replace it with a new nozzle that is suited to the new type of gas (see Burner and nozzle specifications table). Turn the knob to the minimum position (MIN) after it has been in the maximum position (MAX) for approximately 10 minutes. Tighten or loosen the adjustment screws on the outside of the thermostat pin (see figure) until the flame is small but steady. If the appliance is connected to liquid gas, the adjustment screw must be fastened as tightly as possible. Turn the knob from the MAX position to the MIN position quickly or open and shut the oven door, making sure that the burner is not extinguished. May be adapted for use with any Type of gas shown on the data Plate, which is located inside the On the left-hand wall inside the For each BURNER knob there is a complete ring showing the strength of the flame for the relevant burner. Press the BURNER knob and turn it in an anticlockwise direction so that it is pointing to the maximum flame setting . Adjust the intensity of the flame to the desired level by turning the BURNER knob in an anticlockwise direction. This may be the minimum setting , the maximum setting or any position in between the two. If the appliance is fitted with The symbol , then hold The BURNER knob down Several models are equipped with an ignition device Which is built into the knob; in this case the Simply press the BURNER Knob and turn it in an anticlockwise direction so that It is pointing to the maximum flame setting, until the The burner may be extinguished when If this occurs, repeat the Operation, holding the knob down for a longer period If the flame is accidentally extinguished, switch off the burner and wait for at least 1 minute before attempting to relight it. If the appliance is equipped with a flame failure safety device (X), press and hold the BURNER knob for approximately 2-3 seconds to keep the flame alight and to activate the device. To switch the burner off, turn the knob until it reaches the stop position · Practical advice on using the burners For the burners to work in the most efficient way possible and to save on the amount of gas consumed, it is recommended that only pans that have a lid and a flat base are used. To identify the type of burner, please refer to the diagrams contained in the "Burner and nozzle specifications". The first time you use your appliance, heat the empty oven with its door closed at its maximum temperature for at least half an hour. Ensure that the room is well ventilated before switching the oven off and opening the oven door. The appliance may emit a slightly unpleasant odour caused by protective substances used during the manufacturing process burning away. Before operating the product, remove all plastic film from the sides of the appliance. Never put objects directly on the bottom of the oven; this will avoid the enamel coating being damaged. Only use position 1 in the oven when cooking with the rotisserie spit. To light the oven burner, bring a flame or gas lighter close to opening F (see figure) and press the OVEN control knob while turning it in an F anticlockwise direction until it reaches the MAX position. If, after 15 seconds, the burner is still not alight, release the knob, open the oven door and wait for at least 1 minute before trying to light it again. The oven is fitted with a safety device and it is therefore necessary to hold the OVEN control knob down for approximately 6 seconds. [. . . ] Stainless steel can be marked by hard water that has been left on the surface for a long time, or by aggressive detergents containing phosphorus. GB If the cooker is fitted with a glass cover, this cover should be cleaned using lukewarm water. It is possible to remove the cover in order to make cleaning the area behind the hob easier. Do not close the cover when the burners are alight or when they are still hot. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE INDESIT KN1G20S(W)/I




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual INDESIT KN1G20S(W)/I will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.