User manual I-INC IH253

[. . . ] iH253/iH283 HSG1082/HSG1081 OSD[V4. 392] User's Manual OSD[4. 392] Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Secure the Monitor to the bracket using the 4 mount holes on the back and center of the Monitor. Note: · Please read the instructions of your specific wall bracket to properly wall mount the Monitor. · The pitch of the mounting holes is 100mm horizontally and 100mm vertically. · The Monitor stand base can be screwed on a table or a hard surface using the hole on the back of the stand base. *Installing the LCD Monitor requires special skill that should only be performed by qualified service personnel. I-INC bears no responsibility for improper mounting or mounting that results in accident or injury. You can ask a qualified service personnel about using an optional bracket to mount the Monitor to the wall. 8 User's Manual MAKING CONNECTIONS CONNECTING TO A PC Turn off your computer before performing the procedure below. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer's VGA port. Connect one end of the DVI cable (optional) to the back of the monitor and connect the other end to the computer's DVI port. Connect one end of the HDMI to DVI cable (optional) to the back of the monitor and connect the other end to the computer's DVI port. Connect one end of the HDMI cable (optional) to the back of the monitor and connect the other end to the computer's HDMI port. Connect the audio cable between the monitor's audio input and the PC's audio output (green port). Plug one end of the AC power cord to the LCD monitor's AC input socket, and the other end to Wall outlet. Connecting to a PC 1 3 5 Power AC Input VGA Input HDMI Input (optional) 2 4 6 LINE IN DVI Input (optional) Earphone (optional) 9 User's Manual ADJUSTING THE VIEWING ANGLE · For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. · Hold the stand so you do not topple the monitor when you change the monitor's angle. · You are able to adjust the monitor's angle from 0° to 20° (iH253, iH283). Figure. 3. Monitor Angle NOTES: · Do not touch the LCD screen when you change the angle. · Be careful not to place fingers or hands near the hinges when tilting the monitor, otherwise pinching can result. 10 User's Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. Default isPC. 12 User's Manual Resolution 640x400@70Hz 720x400@70Hz 640x400@85Hz 720x400@85Hz 640x480@60Hz 720x480@60Hz 1024x768@70Hz 1280x768@70Hz 1280x768@60Hz 1360x768@60Hz 1400x1050@60Hz 1680x1050@60Hz 1400x1050@RB 60Hz 1680x1050@RB 60Hz 1400x1050@75Hz 1680x1050@75Hz ** The screen resolutions available will depend on the purchased model. NOTES: · Do not install the monitor in a location near heat sources such as radiators or air dusts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. · Save the original shipping box and packing materials, as they will come in handy if you ever have to ship your monitor. · For maximum protection, repackage your monitor as it was originally packed at the factory. · To keep the monitor looking new, periodically clean it with a soft cloth. [. . . ] The appearance is similar to a "Screen Saver" feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse. 17 User's Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION Power LED is not on POSSIBLE SOLUTION *Check if the Power Switch is in the ON position. *Make sure monitor's video cable is properly connected to the computer. *Inspect monitor's video cable and make sure none of the pins are bent. [. . . ]