User manual HITACHI UT47X902

[. . . ] TM Director's Series HDTV Monitors ® 1. 5" UltraThin Liquid Crystal Display Black Sapphire Crystal Frame 1920 x 1080p with High Efficiency EEFL Backlight (1) HDMITM (V. 1. 3 with CEC) Input; (1) RGB D-sub15 Input with Audio Operating Guide UT37X902 UT42X902 UT47X902 Model Name READ THE ENCLOSED INSTRUCTIONS CAREFULLY. KEEP THIS OPERATING GUIDE FOR FUTURE REFERENCE. Record the serial number of your monitor for future reference. SERIAL NO. This serial number is located on the back and right side of the monitor. ANY QUESTION ABOUT THIS PRODUCT PLEASE CONTACT 800-Hitachi CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . 02 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Each time this button is pressed, the screen displays the corresponding mode in the following sequence. HDMI RGB (/Composite) Input Select button RGB Input Select button HDMI Input Select button Press the or button to directly select the input mode. <From Control panel> The Input modes can also be switched using the Input Select button on the control panel. Each time this button is pressed, the screen displays the corresponding mode in the following sequence. HDMI RGB (/Composite) Input Select NOTE Switching between RGB and Composite Mode When pressing button, you will see the image from either RGB or Composite mode. Select "Composite" to display the image from a video source via the optional D-sub 15 pin - composite cable. See 40 and 41 for details of "RGB input" menu. Input Signal Screen Display The input signal status can be displayed on the screen by pressing the button on the remote control. Input mode HDMI mode HDMI DVI 720p * Signal mode * HDMI-DVI connection only RGB mode Input mode Input horizontal frequency Input vertical frequency INFO button RGB H : 48. 4kHz V : 60. 0 Hz Composite mode Composite 24 ENGLISH Input Switching to HDMI and RGB SETUP OPERATION How to Use the Remote to Control your External Devices OPERATING THE PRECODED FUNCTIONS FOR YOUR EXTERNAL DEVICES. The new remote control is designed to operate different types of VCRs, cable boxes, set-top-boxes, satellite receivers, DVD players, and other audio/video equipment. You must first program the remote to match the remote system of your external equipment (refer to pages 31 ~ 32 for precodes). Select the desired device mode DVD, PVR/VCR, SAT/CBL or AVR by pressing the corresponding device button. Hold down the device button (DVD, PVR/VCR, SAT/CBL or AVR) on the remote and enter the four digit preset code that matches your device as shown on pages 31 ~ 32 . If done correctly, the device LED indicator will blink 3 times to confirm proper setup. The remote will now control the desired device. Power button Device buttons Numeric buttons 4. Select Cable mode by using your SAT/CBL button to position the LED indicator on SAT/CBL. Hold down the SAT/CBL button on the remote and press the numbers 0, 0, 0 and 3. The remote will turn off your cable box when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different four digit preset code. The remote will now control your Cable box. Remote Control Backlight Feature When you press any remote control button, the buttons will light up. The buttons will appear to light if the room is dark. 7. Repeat the same procedure for your set-top-box or satellite receiver (select SAT/CBL), your DVD (select DVD), your VCR/PVR(select VCR/PVR), or your AVR (select AVR). NOTE Disabling Remote Control Backlight Feature 1. To re-enable the backlight feature do steps 1~3 again (these steps toggle the Backlight Feature on and off, default is ON). If your external device cannot be operated after performing the above procedures, your external device code has not been precoded into the remote. In the unlikely event that your external device cannot be operated after performing the above procedures, please consult your external device operating guide. The remote control will remember the codes you have programmed even after the batteries are removed from the remote control. To reset all programmed codes to factory default place remote control in TV mode, then press and hold TV mode key and enter "9", "8", "1" in sequence. [. . . ] You understand and agree that your use of the Software in any manner except as permitted under this Agreement could constitute a serious crime and could subject you to damages and an award to HITACHI of attorneys' fees in connection with your violation of this Agreement. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights caused or facilitated by your failure to abide by the terms of this Agreement. You agree to defend, indemnify and hold HITACHI and its parent and affiliate companies harmless from and against any and all liability resulting from any breach by you of this Agreement. The Software is protected by federal copyright laws, international copyright treaties and other intellectual property laws and treaties. [. . . ]