User manual HITACHI UT32X802

[. . . ] TM Director's Series 32" HDTV Monitor ® 1. 5" UltraThin Liquid Crystal Display Black Sapphire Crystal Frame 1366 x 768p with High Efficiency EEFL Backlight (1) HDMITM (V. 1. 3 with CEC) Input; (1) RGB D-sub15 Input with Audio Operating Guide UT32X802 Model Name READ THE ENCLOSED INSTRUCTIONS CAREFULLY. KEEP THIS OPERATING GUIDE FOR FUTURE REFERENCE. Record the serial number of your monitor for future reference. SERIAL NO. This serial number is located on the back and right side of the monitor. CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . 02 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 Trademark Credits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After turning On, it takes about 6 seconds until the monitor starts up. Please note that buttons on the remote control and the unit (such as the Power button) do not work during this period of time. If power is interrupted during use of the unit, to avoid sudden surges of electricity when the power comes back on, turn off the main power to the unit before leaving home. BASIC OPERATION (continued) Volume Up/Down 1. To increase the sound volume, press the Volume Up button on the remote control or control panel. To decrease the sound volume, press the Volume Down button on the remote control or control panel. The color of the Volume Indicator will turn into grey while muting the volume. To turn the sound back on, press the button again, or press the Volume Up button on either the remote control or control panel. The color of the Volume Indicator will turn back to blue. NOTE Volume Up/Down button 20 You can decrease the volume by pressing the Volume Down button while the sound is muted. 23 BASIC OPERATION (continued) Menu button By pressing the Input Select button , you can switch the input to display the image outputting from the external equipment connected to each terminal (HDMI and RGB (/Composite)). Each time this button is pressed, the screen displays the corresponding mode in the following sequence. HDMI RGB (/Composite) Input Select button RGB Input Select button HDMI Input Select button Press the or button to directly select the input mode. <From Control panel> The Input modes can also be switched using the Input Select button on the control panel. Each time this button is pressed, the screen displays the corresponding mode in the following sequence. HDMI RGB (/Composite) Input Select NOTE Switching between RGB and Composite Mode When pressing button, you will see the image from either RGB or Composite mode. Select "Composite" to display the image from a video source via the optional D-sub 15 pin - composite cable. See 40 and 41 for details of "RGB input" menu. Input Signal Screen Display The input signal status can be displayed on the screen by pressing the button on the remote control. Input mode HDMI mode HDMI DVI 720p * Signal mode * HDMI-DVI connection only RGB mode Input mode Input horizontal frequency Input vertical frequency INFO button RGB H : 48. 4kHz V : 60. 0 Hz Composite mode Composite 24 ENGLISH Input Switching to HDMI and RGB SETUP OPERATION How to Use the Remote to Control your External Devices OPERATING THE PRECODED FUNCTIONS FOR YOUR EXTERNAL DEVICES. The new remote control is designed to operate different types of VCRs, cable boxes, set-top-boxes, satellite receivers, DVD players, and other audio/video equipment. You must first program the remote to match the remote system of your external equipment (refer to pages 31 ~ 32 for precodes). Select the desired device mode DVD, PVR/VCR, SAT/CBL or AVR by pressing the corresponding device button. Hold down the device button (DVD, PVR/VCR, SAT/CBL or AVR) on the remote and enter the four digit preset code that matches your device as shown on pages 31 ~ 32 . If done correctly, the device LED indicator will blink 3 times to confirm proper setup. The remote will now control the desired device. Power button Device buttons Numeric buttons 4. Select Cable mode by using your SAT/CBL button to position the LED indicator on SAT/CBL. Hold down the SAT/CBL button on the remote and press the numbers 0, 0, 0 and 3. The remote will turn off your cable box when the correct four digit preset code is entered. [. . . ] You understand and agree that your use of the Software in any manner except as permitted under this Agreement could constitute a serious crime and could subject you to damages and an award to HITACHI of attorneys' fees in connection with your violation of this Agreement. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights caused or facilitated by your failure to abide by the terms of this Agreement. You agree to defend, indemnify and hold HITACHI and its parent and affiliate companies harmless from and against any and all liability resulting from any breach by you of this Agreement. The Software is protected by federal copyright laws, international copyright treaties and other intellectual property laws and treaties. [. . . ]