User manual HITACHI R-Z660ERU6XD

[. . . ] CAUTION This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling. NOTE · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual. · The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent. [. . . ] When the slant of the projector is changed, execute this function again. · The adjustable range of this function will vary among inputs. · When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly. · When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible. · When the projector is placed on the level (about ±3°), this function may not work. · When the projector is inclined to near ±30 degree or over, this function may not work well. · When the vertical lens shift is not set fully upward (not set fully downward for the optional lens type FL-601 only (45)), this function may not work well. · When the horizontal lens shift is not set to the center, this function may not work well. · This function will be unavailable when the Transition Detector is on (51). Shrink the top of the image ó Shrink the bottom of the image · The adjustable range of this function will vary among inputs. To quit the operation, press the MENU button on the remote control or keep no operation for about 10 seconds. The blank screen is a screen for the temporarily blanking feature (22). MyScreen ó ORIGINAL ó BLUE ó WHITE ó BLACK BLANK MyScreen ORIGINAL BLUE, WHITE, BLACK Feature Screen can be registered by the MyScreen item (40). Screen preset as the standard screen. Plain screens in each color. · To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the plain black screen after several minutes. (continued on next page) 38 SCREEN Menu SCREEN Menu (continued) Item Description Using the / buttons switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected. MyScreen ó ORIGINAL ó TURN OFF Feature Screen can be registered by the MyScreen item MyScreen START UP (40). ORIGINAL TURN OFF Screen preset as the standard screen. Plain black screen. · To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the BLANK screen (38) after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, the plain black screen is instead used. · When the TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu (48), the START UP is fixed to MyScreen. (continued on next page) 39 SCREEN Menu SCREEN Menu (continued) Item Description This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. [. . . ] The main power source has been interrupted during operation such as by a power outage (blackout), etc. Please turn the power off, and allow the projector to cool down at least 2 minutes, then turn the power on again. 6 Either there is no lamp and/or lamp cover, or either of these has not been properly fixed. Please turn the power off, and allow the projector to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again. 60 The signal cables are not correctly connected. Correctly connect the connection cables. 0 ­ 17, 18 Signal source does not correctly work. Neither sounds nor pictures are outputted. Correctly set up the signal source device by referring to the manual of the source device. The input changeover settings are mismatched. Select the input signal, and correct the settings. The BLANK function for pictures and the MUTE function for sounds are working. (Continued on next page) AV Mute may be active. Refer to the item "Sound does not come out" and "No pictures are displayed" on the next page to turn off the MUTE and BLANK functions. 17, 22 69 Troubleshooting Phenomena that may be easily mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect Reference page 0 7 The signal cables are not correctly connected. Correctly connect the audio cables. The MUTE function is working. Restore the sound pressing the MUTE or VOLUME button on the remote control. The volume is adjusted to an extremely low level. Sound does not come out. Adjust the volume to a higher level using the menu function or the remote control. 7 37 37 0 3, 16 0 25, 26 The AUDIO setting is not correct. Correctly set the items in the AUDIO menu. The audio on your HDMI equipment is not set to Linear PCM. The audio on the HDMI input is muted. The HDMI input on this projector supports Linear PCM audio only. [. . . ]