User manual HITACHI MP-EG10W

[. . . ] 2000 Sierra Point Parkway Brisbane, Ca 94005-1835 Hitachi Sales Corporation of Hawaii 3219 Koapaka St, Honolulu, HI 96819 Tel. Please take time to become familiar with this manual and how it is set up. 1998 Printed in Japan KY-Y(N) Chapter 1 Introduction This section gives you how to use your MP-EG10W efficiently, and explains the overview of your MP-EG10W. Before using it, read this section thoroughly. Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] E72 ______Chapter 4 Using Media Navigation (Playback) Switching Thumbnail Display On or Off You can switch the thumbnail display on and off with the file select screen. If thumbnail display is switched off, you can display six files on the screen at a time. * Start Media Navigation (see page 42) and display the FOLDER select screen to start. * You can also use the remote control to operate. 2 3 1 1 Display the file select screen. File select screen (3-thumbnail display) Press v or w with the FOLDER select screen to select a folder with files, and press. * It has been set at the factory that the three-thumbnail file select screen will appear first, but subsequently, the file select screen designated previously will appear. * When Media Navigation is started immediately after recording, the three-thumbnail file select screen will appear. * Even if the folder is changed, the thumbnail display method will not change. * When you switch off a thumbnail, no thumbnails will be displayed no matter which folders you select. 2 Display a 9-thumbnail file select screen. Press the REC MODE/THUMBNAIL button, and a 9-thumbnail file select screen will appear. File select screen (9-thumbnail display) 3 Display a file select screen without thumbnails. Press the REC MODE/THUMBNAIL button again. Thumbnails will disappear and six files will be displayed on one screen. * You cannot switch on or off the thumbnail display while the menu is displayed, a folder is being changed (see page 50), or the recording date/time are being changed (see page 64). File select screen (without thumbnails) If the thumbnail display is not possible with files recorded by equipment other than MP-EG10W, appear in place of thumbnails. will E73 Chapter 4 Using Media Navigation (Playback) ______ Correcting File Recording Date/Time (CHG TIME menu item) When the internal clock goes wrong because of consumption of the built-in battery, the date and time on which you start to record will not be recorded correctly. In this case, charge the built-in battery, correct the clock, and also correct the file recording date/time by the following procedure. There are two ways of changing the recording date/time: changing all files in folder to the same date/time, or designating files in folder and changing their recording date/time. To change all files in folder to the same recording date/time: _ * Start Media Navigation (see page 42) and display the FOLDER select screen to start. * Using the MACRO/SHIFT button allows you to change all files in multiple folders to the same recording date/time in one step. 5 2 1 6 3 4 6 1 Display the menu and select CHG TIME. Press the MENU button to display the menu, and press w to select CHG TIME. 2 Display the screen for correcting the recording date/time. Press s. The menu will disappear and the screen for correcting the recording data/time will appear. 3 Select the folder where you want to correct the recording date/time. Press w or v to select the file whose recording date/time you want to correct, and then press s. You can select multiple files by pressing the MACRO/SHIFT button (see page 45). E74 ______Chapter 4 Using Media Navigation (Playback) 4 Correct the recording date/time. The number of year for the selected file in folder will be highlighted. Press s or t to highlight the number you want to correct, and then press v or w to increase or decrease it. * The seconds display counts up or down in 2-seconds unit. 5 Enter the corrected date/time. After correcting all the incorrect numbers, press the REC/PAUSE button. You can continue to change file recording date/time by repeating steps 3-5. * To cancel change or recording date/time, press the MENU button before pressing REC/PAUSE. The recording date/time will not change, and recording date/time change menu will finish. 6 Exit the CHG TIME menu item. Press the t button or menu button. Press t exits the recording date/time correct menu item and restores the folder function setting menu (the screen in step 1). Pressing MENU exits the recording date/time correct menu item and restores the folder select screen. To designate a file in folder and change its recording date/time: _______ * Start Media Navigation (see page 42) and display the FOLDER select screen to start. [. . . ] You can select one of four modes: : Moving picture (MPEG1 Format) : Still picture (JPEG Format) : Consecutive recording of still pictures (JPEG Format, 2 pictures/sec. and 5 shots) : Still picture with audio (JPEG Format and MPEG Audio) When still pictures are input from external equipment: : Still picture (2-field input) appears, instead of . (See pages 82 and 83) e Lap time: This appears when you select moving pictures or still picture with audio, and indicates the elapsed time since the REC button was pressed. r Zoom bar: This appears when the ZOOM/VOL button is pressed during recording, and indicates the zoom setting among 10 settings from W (wide) to T (tele), and M (macro). [. . . ]