User manual HITACHI L19HP03UA

[. . . ] Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can edit the list via GREEN key and delete with the RED button. Conditional Access · Press the MENU button to display the main menu and use the " " or " " button to highlight the "Conditional Access" line and press the OK button: Program Guide This section is same with the instructions given in the General Operations page. Please see Electronic Programme Guide (EPG) section in the General Operations part. English - 25 - Some Digital Terrestrial channels operate on a Pay Per View basis. Obtain the Conditional Access Module (CAM) and the viewing card by subscribing to a pay channel company, then insert those to the TV using the following procedure. · Insert the CAM and then the viewing card to the slot that is located in the terminal cover at the left-hand side of the TV (from front view). · The CAM should be correctly inserted, it is impossible to insert fully if reversed. The CAM or the TV terminal may be damaged if the CAM is forcefully inserted. · Connect the TV to the mains supply, switch on and then wait for few moments until the card is activated. Please set the CAM by entering the IDTV menu, Conditional Access then pressing the OK button. (CAM set up menu is not displayed when it is not required. ) · To see the viewing contract information: enter IDTV; press the "MENU" button, then highlight Conditional Access and press the OK button. · When no module is inserted, "No Conditional Access module detected" message appears on the screen. · Refer to the module instruction manual for details of the settings. NOTE: Insert or remove the CI module only when the TV is switched off or in standby mode. You can find detailed information for all menu items in "Analogue TV Menu System" section. Setup The adjustments in this menu are given as the following: Configuration You can configure the settings of your TV. Press the EXIT button on the remote control to exit. TV Setup You can use this item to display the TV functions. Press the "MENU" button to display the main menu and use " " or " " button to highlight "TV Setup", press the OK button to display TV Setup menu screen. AC3 Audio (* for EU countries only) In the Configuration Menu, highlight the AC3 Audio item by pressing " " or " " buttons. Use the " " or " " buttons to set the AC3 Audio as On or Off. If the channel that you are watching supports AC3 Audio, turn this setting on. Hard of Hearing (* for EU countries only) Use " " or " " button to select Hard of Hearing and then press " " or " " button to set this setting as On or Off. English - 26 - If the broadcaster enables any special signal concerning the audio, you can set this setting as On to receive such signals. Press " " or " " button to set this function as on or off. Channel List Use " " or " " buttons to go to Channel List option. Use " " or " " buttons to toggle Channel List Mode. If you select "TV Only", with the " " or " " buttons, you navigate through only TV channels. [. . . ] on device) SCL SDA DDC/CED Ground +5V Power Hot Plug Detect Signal Input PC RGB Terminal (D-sub 15-pin connector) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Input signal R G or sync on green B No connection No connection R. GND G. GND B. GND No connection GND No connection [SDA] H. sync or H/V composite sync V. sync. [V. CLK] [SCL] English - 43 - Specifications TV BROADCASTING PAL/SECAM B/G D/K K' I/I' L/L' RECEIVING CHANNELS VHF (BAND I/III) UHF (BAND U) HYPERBAND MHEG-5 ENGINE compliant with ISO/IEC 13522-5 UK engine Profile 1 Object carousel support compliant with ISO/IEC 135818-6 and UK DTT profile Frequency range: 474-850 MHz for UK models Digital Reception 170-862 MHz for EU models Transmission standard: DVB-T. MPEG-2 Demodulation: COFDM with 2K/8K FFT mode FEC: all DVB modes Video: MP@ML, PAL, 4:3/16:9 Audio: MPEG Layer I&II 32/44. 148kHz. for UK NUMBER OF PRESET CHANNELS 200 CHANNEL INDICATOR On Screen Display RF AERIAL INPUT 75 Ohm (unbalanced) OPERATING VOLTAGE 220-240V AC, 50 Hz. [. . . ]