User manual HITACHI J100-E4

[. . . ] 3 About Electro-Magnetic Interference . . . . . . . . . . . . . . . . 3 About Waste Electrical and Electronic Equipment . . . 4 Entries and graphical symbols explanation . . . . . . 2 Important safety instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Contents of package. . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Loading batteries into the remote control . . . . . . . . . 5 Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 1 ENGLISH CP-X2510Z/CP-X3010Z CP-X2011/CP-X2511/J100-E4/CP-X3511 User's Manual (concise) First of all Entries and graphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows, for safety purpose. WARNING This entry warns of a risk of serious personal injury or even death. [. . . ] Ask your dealer about nonaccessory cables which may be required a specific length or a ferrite core by the regulations. For cables with a core only at one end, connect the end with the core to the projector. An incorrect connection may result in malfunction or damage to the device and the projector. NOTICE Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. 7 ENGLISH Connecting power supply the connector 1. In a couple of power supply connection, the POWER indicator will light up in steady orange. Please remember that when the DIRECT ON function activated, the connection of the power supply make the projector turn on. AC IN Power cord WARNING Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock. · Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. · Never modify the power cord. Turning on the power and the outlet. The projection lamp will light up and the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green. is firmly 1. To prepare a new lamp, make contact with your dealer and tell the lamp type number. Prepare aor if the lamp has projectoralso ask the on a ceiling, broken, dealer to replace the lamp. Loosen the screw (marked by arrow) of the lamp cover and then slide and lift the lamp cover to the side to remove it. Loosen the 3 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the handles. Insert the new lamp, and retighten firmly the 3 screws of the lamp that are loosened in the previous process to lock it in place. Lamp cover 3 3. While and thethe interlocking parts of the lamp cover projector together, slide the lamp 7. cover back in place. Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu. (2) Point at the ADVANCED MENU in the menu using the / button, then press the button. (3) Point at the OPTION in the left column of the menu using the /button, then press the button. (4) Point at the LAMP TIME using the / button, then press the button. CAUTION Do not touch any inner space of the projector, while the lamp is taken out. [. . . ] If the air filter becomes clogged by dust or the like, internal temperatures rise and could cause a fire, a burn or malfunction to the projector. NOTE · Please reset the filter time only when you have cleaned or replaced the air filter, for a suitable indication about the air filter. · The projector may display the message such as "CHECK THE AIR FLOW" or turn off the projector, to prevent the internal heat level rising. 14 Using the CD manual The other manuals for this product are written into the included CD-ROM titled "User's Manual (detailed)". Before using the CD-ROM, please read the following to ensure the proper use. System requirements The system for using the CD-ROM requires the following. [. . . ]