User manual HITACHI HDC-651E

[. . . ] HDC-651E 6. 0 2. 4" 3x Optical Zoom FCC STATEMENT (For customers in USA) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Rotate the mode dial to and turn your camera on by pressing the power switch. Press the shutter release button to capture the image. EN-37 PLAYBACK MODE - THE BASICS Viewing Images You can display the still images one by one. Rotate the mode dial to , , , , , or and turn your camera on by pressing the power switch. To view the next image, press the four-way controller ( ). 100-0001 For protected images/movie clips, mark will be displayed. Refer to the section in this manual titled "Protecting Images/Movie Clips" (EN-47) for further details. For images selected for printing with DPOF setting, mark will be displayed. (Refer to the section in this manual titled "Setting the DPOF" (EN-48, 49) for further details. ) If there is no image stored in the internal memory or on the SD memory card, [No image] message will appear on the LCD monitor screen. You cannot enter the Playback mode from the Setup mode. EN-38 Magnifying Images While reviewing your images, you may enlarge a selected portion of an image. The zoom factor displayed on the screen shows the current magnification ratio. To view different portions of the images, press the four-way controller ( ) to adjust the display area. 1. 5X The magnification factors range from 1. 5X to 4X (within 6 stages: 1. 5X, 2. 0X, 2. 5X, 3. 0X, 3. 5X and 4. 0X). EN-39 Thumbnail Display This function allows you to view 9 thumbnail images on the LCD monitor screen simultaneously so you may search for a particular image. (Refer to the section in this manual titled "Protecting Images/ Movie Clips" (EN-47) for further details. ) 3. Use the four-way controller ( ) to move the cursor to select the image to be displayed at regular size. Press the or / button to display the selected image on full screen. 1 2 3 4 5 6 7 8 9 EN-40 Slideshow Display The slideshow function enables you to play your images back automatically in sequential order. This is very useful and entertaining feature for reviewing recorded images and for presentations. Then use the four-way controller ( ) to select [Slide Show] and press the button. Playback1 Playba Slide Sh Show otect Protect Protec DPOF Playback2 Playba Return Retu n : eturn Select : 3. Use the four-way controller ( ) to set the playback interval, then press the button. The movie clips display the first frame image, and the movie is not played back. To stop slideshow, press the button. Cancel : Slide Sh Show 3 Sec. 10 Sec. Start Sta t : You can adjust the slideshow display interval within the range of 3 sec. , 5 sec. , 10 sec. . EN-41 Resizing an Image You can change the image size of a captured image to one of the following sizes: 2272 x 1704 pixel, 1600 x 1200 pixel and 640 x 480 pixel. In the mode, use the four-way controller ( ) to select the desired images. Press the four-way controller ( ) to select [Playback2] and press ( ) to select [Resize] and press the button. Use the four-way controller ( ) to select the desired setting, then press the button to confirm. Playback1 Playba Resize esize Resi Quality Change Copy o Ca Co y To Card Playback2 Playba Return Retu n : eturn Select : Resize Resi esize 2272 X 1704 1600 X 1200 640 X 480 Cancel : Select : You can only choose a smaller size image; you cannot increase the resolution of an image. [. . . ] Sets whether or not to reset the file number when you take photographs. The captured images are recorded to the newly created folder from number 0001. If you want to reset the file number, be sure that no images are recorded in the internal memory or the SD memory card. Set to Default Returns all basic settings to the digital camera s default settings. [. . . ]