User manual HITACHI HDC-1296E

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] To save your corrected image, select [Confirm] with the / buttons, and press the button. When this process ends, this replaces the original image with the corrected image. EN-24 Attaching Voice Memos A maximum of 30 seconds of audio can be recorded as a memo for captured still images. Select the image to which you want to attach the voice memo with the / buttons. Press the [VOICE RECORDING] is displayed on the screen and recording starts. To stop recording a voice memo as it is being recorded, press the button again. [VOICE RECORD END] will be displayed momentarily and the recording will end. An [ ] icon is displayed with images that have been recorded with a voice memo. Playing back voice memo A press of the button displays [VOICE PLAYBACK] and plays back the voice memo. xa E 100- 0001 Voice memo is only available for still images. EN-25 Protecting Images Set the data to read-only to prevent images from being erased by mistake. Protection is applied to the image and the camera returns to the playback mode. When [All] has been selected, [ ] is displayed with all the images. Canceling the Protection To cancel protection for only one image, display the image on which you want to remove the image protection. Select the image that you want to cancel protection with the / buttons. The removal of image protection is executed and the camera returns to the playback mode. Formatting an SD/SDHC memory card overrides protection, and erases all images regardless of their protected status. EN-26 DPOF Settings DPOF is the abbreviation for Digital Print Order Format, which allows you to embed printing information on your memory card. You can select the images to be printed and how many prints to make with the DPOF menu in the camera and insert the memory card to the card compatible printer. When the printer starts printing, it will read the embedded information on the memory card and print the specified images. Select date to [On] or [Off] with the / buttons, and press the button. This creates a file containing the DPOF information, and when the operation is finished, the screen returns to the playback mode. The DPOF icon [ ] is displayed on each image that has set up DPOF settings. x 1 E 100- 0001 The date that is printed on the image is the date set on the camera. To print the correct date on the image, set the date on the camera before you capture the image. Refer to the section in this manual titled "Setting the Date and Time" for further details. EN-27 Erasing Images Erasing a single image / Erasing all images 1. To exit from the menu, press the button. Deleting an image will not affect sequential image numbering. For example, if you delete image number 240, the next captured image will be numbered 241 even though 240 no longer exists. In other words, an image-number is retired when an image is deleted and will not be reused or reassigned to another subsequently captured image. EN-28 MENU OPTIONS Capture Menu This menu is for the basic settings to be used when capturing still images. Function 1. Press the button, and select the [Capture] / [Function] menu with the / buttons. [. . . ] If the batteries or accumulators included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0. 0005% Mercury, or more than 0. 002% Cadmium or more than, 0. 004% Lead. Le marquage est en conformité avec la directive 2002/96/EC du DEEE (déchets d'équipements électriques et électroniques). Ce symbole indique l'obligation de ne pas déposer ce produit, y compris les batteries et accumulateurs vides ou déchargés, dans des décharges publiques, mais d'utiliser les systèmes spécifiques de retour et récupération disponibles. Si sur les piles ou accumulateurs inclus avec cet appareil, le symbole chimique Hg, Cd ou Pb est visible, cela signifie que la batterie a une teneur en métaux lourds de plus de 0. 0005% de mercure, ou plus de 0, 002% de cadmium, ou plus de 0, 004 % Plomb. [. . . ]