User manual HITACHI HDC-1097E

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Press the button, and select the [Capture] / [Function] menu with the / buttons. Select the desired option item with the / buttons, and press the button to enter its respective menu. *[ ] 3648 x 2736 *[ ] 2816 x 2112 *[ ] 2272 x 1704 *[ ] 1600 x 1200 *[ ] 640 x 480 Quality This sets the quality (compression) at which the image is captured. *[ ] Fine *[ ] Standard *[ ] Economy Sharpness This sets the sharpness of the image that will be captured. * Hard / Standard / Soft Saturation This sets the saturation of the image that will be captured. Balance This sets the white balance for a variety of lighting conditions and permits images to be captured that approach the conditions that are seen by the human eye. *[ ] Fluoresc. 1 *[ ] Fluoresc. 2 *[ ] Daylight *[ ] Cloudy *[ ] Manual WB ISO This sets the sensitivity for capturing images. When the sensitivity is raised (and the ISO figure is increased), photography will become possible even in dark locations, but the more pixelated (grainier) the image will appear. * [Blank] Auto *[ ] ISO 64 *[ ] ISO 100 *[ ] ISO 200 *[ ] ISO 400 *[ ] ISO 800 *[ ] ISO 1600 Metering This sets the metering method for calculating the exposure. * Center: Averages the light metered from the entire frame, but gives greater weight to the subject matter at the center. * Spot: A very small portion of the center of the screen is measured to calculate the correct exposure. * Standard / Vivid / Sepia / B&W / Blue / Red / Green / Yellow / Purple EN-28 Capture Md. * [Blank] Single: Captures one image at a time. *[ *[ *[ *[ ] ] ] ] Continuous: Permits continuous capture of up to 3 images. AEB: Permits 3 consecutive images in the order of standard exposure, underexposure and overexposure compensation. Album Shot: Creates an album-like layout to combine 3 shots into a single image. Burst: Permits continuous photography while pressing and holding the shutter button. As long as you hold the shutter button pressed, images are captured until the memory capacity is exhausted. Pre-shot: Lets you capture the background first, then have someone to capture you in front of it. You can include yourself in the shot. *[ *[ *[ ] ] ] Quick Shot If this function is set to "On", the camera takes a quick shot without focusing. Zoom This sets whether or not to use digital zoom at the time of photography. * On / Off Preview This sets whether or not to display the captured image on the screen immediately after the image is captured. * On / Off Date Print The date of recording can be printed directly on the still images. [. . . ] If the batteries or accumulators included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0. 0005% Mercury, or more than 0. 002% Cadmium or more than, 0. 004% Lead. Le marquage est en conformité avec la directive 2002/96/EC du DEEE (déchets d'équipements électriques et électroniques). Ce symbole indique l'obligation de ne pas déposer ce produit, y compris les batteries et accumulateurs vides ou déchargés, dans des décharges publiques, mais d'utiliser les systèmes spécifiques de retour et récupération disponibles. Si sur les piles ou accumulateurs inclus avec cet appareil, le symbole chimique Hg, Cd ou Pb est visible, cela signifie que la batterie a une teneur en métaux lourds de plus de 0. 0005% de mercure, ou plus de 0, 002% de cadmium, ou plus de 0, 004 % Plomb. [. . . ]