User manual HITACHI GD-2000

[. . . ] Publication Number: GD-2000 DVD-ROM Manual - Page GD-2000 Manual 6/18/98 5:21 PM Page 3 For USA Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC RULES. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The inclination of your DVD-ROM drive should be within 5û as shown below. The following can occur if these requirements are not followed: · The disc may jump out and be damaged when the tray is opened. · Your DVD-ROM drive may not function at full performance. 5û 5û 5û 5û GD-2000 DVD-ROM Manual - Page GD-2000 Manual 6/18/98 5:23 PM Page 7 · Mounting screw The screws must be ISO (M3X0. 5) to mount the DVD-ROM drive tightly and to avoid damaging the mechanism inside the DVD-ROM drive. (See page 10) · Moving your DVD-ROM drive Remove the disc and close the disc tray before moving the DVD-ROM drive. If your DVD-ROM drive is moved with the disc loaded or the disc tray opened, both the disc and the DVD-ROM drive may be damaged. Precautions For Care · Cleaning of the DVD-ROM drive, discs · Never clean your DVD-ROM drive and discs with silicon cloths or cloths soaked in water, solvents (thinner, benzine), abrasive cleaner, anti-static sprays, any record cleaner sprays, liquid cleaner or aerosol cleaner. It may damage or discolor the coating of the DVD-ROM drive and damage or deform discs. · Clean your DVD-ROM drive including the disc tray and discs with a clean, dry, soft cloth at least once a month. · Cleaning of disc If you begin to get error messages that your drive is unable to read a disc, it may mean that cleaning is needed. Clean your DVD-ROM drive's pick-up lens using a cleaning disc. GD 2000 DVD ROM Manual Page GD-2000 Manual 6/18/98 5:24 PM Page 8 Controls and Functions 6 7 Front Rear 34 12 5 89 10 11 1) DVD INDICATOR Indicator lights green when DVD-ROM media is detected in the drive. 2) LOADING/UNLOADING/BUSY INDICATOR Indicator blinks amber only when the disc tray is being opened or closed, or when the DVD-ROM drive is accessing data. 3) HEADPHONE JACK ( 3. 5 mm) 4) HEADPHONE VOLUME CONTROL Adjust the headphone volume. 5) OPEN/CLOSE BUTTON Press this button to open or close the disc tray. 6) DISC TRAY When the power of the DVD-ROM drive is turned off, the disc tray cannot be opened and closed. If the disc tray does not open when the OPEN/CLOSE button is pressed, the DVD-ROM drive's Manual Emergency Eject mechanism may be activated. (See page 12 about Manual Emergency Eject Procedure) 8) AUDIO OUTPUT TERMINAL Circuit Board Rch GND Lch GD-2000 DVD-ROM Manual - Page GD-2000 Manual 6/18/98 5:25 PM Page 9 9) DEVICE CONFIGURATION JUMPER This connector is used to set operation modes such as Master, Slave and CSEL 642 Device is Master 531 or (default setting) Device is Slave Cable Select 10) ATAPI INTERFACE CONNECTOR ATAPI bus connection (40 pin) 11) POWER SUPPLY CONNECTOR (DC Input) For connecting the power supply cable. Circuit Board +5V GND +12V Installation Requirements HARDWARE · · · · · DVD-ROM drive Interface card Interface cable Power supply cable Mounting screws GD 2000 DVD ROM M l P GD-2000 Manual 6/18/98 5:25 PM Page 10 HARDWARE OPTION · Audio connecting cable · Sound card SOFTWARE · DVD-ROM device driver NOTE: If you need an interface card, interface cable or DVD-ROM device driver, contact your dealer. Hardware Installation To install this DVD-ROM drive in the host computer, refer to the instruction manual of each host computer. To install the interface card in the host computer, refer to the instruction manual of each host computer and each interface card. Install the DVD-ROM drive following the general installation procedure shown below: 1) Check the Device Configuration Jumper Settings of the DVD-ROM drive such as Master, Slave, CSEL. (See page 9) 2) Turn off the host computer and unplug the power supply cable of the host computer. 4) Install the DVD-ROM drive into the host computer and mount tightly with screws. 7) Firmly attach the interface cable from the interface card to the DVD-ROM drive. [. . . ] Turn off the DVD-ROM drive and wait at least 15 seconds until the disc stops rotating. Insert the Eject Bar (for example, a straightened paper clip) into the Manual Emergency Eject Hole about 25 mm (1 inch). NOTE: If it is necessary to use the emergency eject procedure to open the drive, the tray should be closed by turning on the power and pressing the OPEN/CLOSE button. Give each device a different Configuration Jumper Setting. The Disc Tray cannot be opened. [. . . ]