User manual HITACHI ED-PJ32

[. . . ] User's Manual ­ Operating Guide ENGLISH EDPJ32 Thank you for purchasing this projector. WARNING Before using this product, please read the "User's Manual Safety Guide" and related manuals to ensure the proper use of this product. NOTE · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual. [. . . ] #1 DEFAULT #1 CUSTOM #2 DEFAULT #3 CUSTOM #3 DEFAULT #2 CUSTOM To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM Selecting a mode of CUSTOM and then pressing the button or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones. Choose an item using the buttons /, and adjust the level using the buttons /. Using a test pattern DEFAULT CUSTOM DEFAULT CUSTOM DEFAULT CUSTOM #3 1 23 4 ENTER : 56 7 8 GAMMA +0 +0 +0 +0 +0 +0 +0 +0 GAMMA [CUSTOM 1] You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. No pattern Gray scale of 9 steps Ramp Gray scale of 15 steps The eight equalizing bars correspond to eight tone levels of test pattern except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar "1". The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar. 33 ENGLISH Multifunctional settings PICTURE menu (continued) Item Description Using the buttons / switches the mode of color temperature. HIGH MIDDLE CUSTOM LOW +0 +0 +0 +0 +0 +0 To adjust CUSTOM Selecting the CUSTOM and then pressing the ENTER : button or the ENTER button displays a dialog OFFSET GAIN RGB RGB to aid you in adjusting the OFFSET and/or GAIN of the CUSTOM mode. OFFSET adjustments change the color intensity +0 +0 +0 +0 +0 +0 on the whole tones of the test pattern. COLOR TEMP GAIN adjustments mainly affect color intensity on the brighter tones of the test pattern. Choose an item using the buttons /, and adjust the level using the buttons /. COLOR TEMP [RGB] HIGH MIDDLE LOW CUSTOM OFFSET RGB :SELECT GAIN RGB COLOR TEMP Using a test pattern You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. No pattern Gray scale of 9 steps Ramp Gray scale of 15 steps COLOR Using the buttons / adjusts the strength of whole color. Strong Weak · This item can be chosen only for a video signal. Green Red · This item can be selected only for a video signal. Strong Weak TINT SHARPNESS 34 Multifunctional settings PICTURE menu (continued) Item Description Using the buttons / switches the progress mode. TV FILM TURN OFF · This function is performed only for an interlaced signal of a VIDEO input, an S-VIDEO input or a component video input of 525i (480i) or 625i (576i) signal. · When the TV or FILM is selected, the screen image will be sharp. The FILM mode can also be used for the 2-3 Pull-Down conversion system (not be used for the 2-2 Pull-Down system). But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select the TURN OFF, even though the screen image may lose the sharp. Choosing a mode of MY MEMORY using the buttons / and then pressing the button or the ENTER button performs each function. LOAD1 LOAD2 LOAD3 LOAD4 SAVE4 SAVE3 SAVE2 SAVE1 This projector has 4 numbered memories for adjustment data. [. . . ] After making sure that the smoke or odor has stopped, contact your dealer or service company. Phenomenon Cases not involving a machine defect The electrical power cord is not plugged in. The main power source has been interrupted during Power does not operation such as by a power outage (blackout), etc. Please turn the power off, and allow the unit to cool down at come on. After the projector has sufficiently cooled down, please turn the power on again. [. . . ]