User manual HITACHI CP-X995

[. . . ] CP-X990W / CP-X995W USER'S MANUAL Please read this user's manual thoroughly to ensure correct usage through understanding. TECHNICAL REGULATORY NOTICES ENGLISH Liquid Crystal Projector Liquid Crystal Projector Thank you for purchasing this liquid crystal projector. WARNING · Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. [. . . ] / button. GAMMA Select Gamma Mode: Select the gamma mode with the NORMAL CINEMA DYNAMIC ENGLISH-14 OPERATIONS (continued) SETUP INPUT IMAGE OPT. Select an item with the and buttons, and start operation. VOLUME MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER Table 7. Options Menu Item VOLUME MENU COLOR LANGUAGE Description Volume Adjustment: Reduce VOLUME Increase VOLUME Select Menu Background Color: Select with the Operation Start/Stop: Press the / button. Select Menu Display Language: Select with the and buttons. and buttons. AUTO OFF Operation Start/Stop: Press the / button. The system automatically enters the standby mode when a signal is not received for the set time. When STOP is selected the system does not enter the standby mode even if no signal is received. SYNC ON G Invalid: Select TURN OFF with the button. · May not be displayed correctly with some input signals when SYNC ON G is valid. In such cases, remove the signal connector so that no signal is received, set SYNC ON G to invalid, and reconnect the signal. SYNC ON G WHISPER Set / Crear WHISPER Mode: Press the / button. In the WHISPER mode, acoustic noise level from the unit is reduced, and brightness level on screen is a little lower. ENGLISH-15 ENGLISH Options Menu OPERATIONS (continued) No Signal Menu The same adjustments and settings are available with the Image and Options menus when the MENU button is pressed during display of the "NO INPUT IS DETECTED ON ***" or "SYNC IS OUT OF RANGE ON ***" message while no signal is received. VOLUME BLANK START UP MIRROR MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER 16 Table 8. No Signal Menu Item VOLUME Description Volume Adjustment: Reduce VOLUME Increase VOLUME · When this function is used, audio input is automatically switched to video. The audio input can be switched by moving the DISK PAD left and right during the display of the volume adjustment bar. The volume adjustment bar is displayed by pressing VOLUME or VOLUME button. Select Blank Screen: Select the screen in case of the BLANK mode with the / button. The selected one (MyScreen, ORIGIAL or one colors) is displayed when the BLANK mode is ON. · When MyScreen or ORIGIAL is selected, the screen is going to the black after several minutes. Select Start Up Screen:Select the screen in case of no signal input with the / button. The selected one (MyScreen, ORIGIAL or TURN OFF) is displayed when no signal is input MyScreen is a mode that the customer-customized screen is displayed. · When MyScreen or ORIGIAL is selected, the screen is going to the black after several minutes. buttons. BLANK START UP MIRROR MENU COLOR LANGUAGE Select Menu Background Color: Select the color with the Operation Start/Stop: Press the / button. Select Menu Display Language: Select the language with the AUTO OFF Operation start/stop: Press the / button. The system automatically enters the standby mode when a signal is not received for the set time. When the STOP is selected the system does not enter the standby mode even if no signal is received. · May not be displayed correctly with some input signals when the SYNC ON G is valid. [. . . ] (3) The projector returns the response code `06H' to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data (`05H'+`00H'+ type (2 bytes) +`00H' + `00H') to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code `06H' to the computer. When a command sent by the projector cannot be understood by the computer When the command sent by the projector cannot be understood, the error command `15H' is returned by the computer. Some times, the projector ignores RS-232C commands during other works. [. . . ]