User manual HITACHI CPX970

[. . . ] If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferable a qualified electrician. [. . . ] Power on all connected equipment. The method of connecting various equipment, see on the page 20~28. Press the INPUT button or the INPUT SELECT (VIDEO or RGB) button to select the source of the signal to be projected on the screen. Example on-screen display · The selected signal input is displayed at the bottom right of the screen for 3 seconds. RGB1 13 ENGLISH 4 2 STANDBY/ON MUTE FREEZE Basic operations (continued) To turn off the power 1 STANDBY/ON 1 INPUT STANDBY/ON MUTE FREEZE MAGNIFY VOLUME OFF 3 MUTE POSITION ON LASER MENU RESET RESET MENU ON BLANK RGB INPUT RIGHT MOUSE ON TIMER VIDEO 2 1 2 3 Press the STANDBY/ON button, for 1 second. · The ON indicator blinks orange and the lamp turns off. (About 1 minute later), the fan stops and the indicator lights up orange. · Press the STANDBY/ON button for short time (less than 1 second), the projector do not set in standby mode. Turn the MAIN POWER switch of the projector off. [ Install the lens cap. : OFF] Caution · To reduce temperature inside the projector, fan will rotate for about 1 minute after the lamp is turned off. · Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged. PLUG&PLAY This projector complies with VESA DDC1/2B specifications. PLUG&PLAY is a system with computer, peripherals (including projectors), and operating system. It works when the projector is connected to DDC (Display Data Channel) ready computer that is running an operating system software that incorporates plug & play functionality. (Only RGB 1) 14 Basic operations (continued) FREEZE FUNCTION 1 2 Press the FREEZE button. The display image stops. A mark appears at the lower right of the screen for about 3 seconds during the FREEZE function. 1, 2 MAGNIFY VOLUME OFF POSITION ON LASER [TO RELEASE FREEZE] Press the FREEZE button. The freeze function is cancelled. mark appears at the bottom of the screen for 3 Caution · Note: When the FREEZE Button is pressed, FREEZE and RELEASE can function alternately. · What is more, FREEZE is released when an input selector button is pressed or when the display mode of a personal computer is switched over during display. When the auto-adjustment is completed the word <AUTO> will disappear. The auto-adjustment of the white level is cancelled by input switching and signal mode change. Caution AUTO · When start up screen is displayed ("NO INPUT IS DETECTED" or "SYNC IS OUT OF RANGE" is displayed), SETUP menu items other than VOLUME cannot be set. · TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input. · V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted with a VIDEO signal input. · Auto-adjustment will take about 10 to 15 seconds to complete. · In some cases auto-adjustment may not function normally, depending on the type of computer to which the unit is connected, and the signal sent. · Carry out the auto-adjustment when the application, which is activated on the computer, is set to the maximum display. · After auto-adjustment the screen may become slightly dark due to the auto-adjustment of the signal level. · Auto-adjust can not be performed during freeze, during magnify, or during the initial screen display ("NO INPUT IS DETECTED" or "SYNC IS OUT OF RANGE"). INPUT The menu INPUT serves for the selection of input source. SETUP INPUT IMAGE OPT. SYSTEM AUTO NTSC PAL SECAM NTSC4. 43 M-PAL N-PAL RGB1 RGB2 VIDEO RGB1 RGB2 V I DEO Adjustment Item RGB 1 RGB 2 VIDEO Selects the RGB 1 terminal. [. . . ] 2) Press the RESET button on projector or remote control MENU ON button during displaying the lamp used time. 3) Select the "0" on the screen using the MENU ( ) button or DISK PAD. LAMP 1700 h 0 CANCEL 31 ENGLISH Lamp cover Message table (continued) Indicator display ON indicator Lights orange Blinks green Lights green Blinks orange Lights red Goes off Goes off Goes off Goes off Lights red The ON indicator, LAMP indicator and TEMP indicator will light or blink in the following cases. Meaning Standby mode During warming up During operation *1 During cooling down Lamp cannot light *2 Cool projector by power off for 45 minutes. Remedy LAMP indicator TEMP indicator Goes off Goes off Goes off Goes off Goes off Lights red Lights red Blinks red Blinks red Goes off Blinks red Goes off Blinks red Goes off Lamp is not inserted or the Securely insert the lamp or close the lamp door open lamp door. The total lamp service time has exceeded the lamp Call a maintenance person. [. . . ]