User manual HITACHI CP-X270

[. . . ] Liquid Crystal Projector ENGLISH USER'S MANUAL Thank you for purchasing this liquid crystal projector. Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE: · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual · The reproduction, transmission or use of this document or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGMENT: · PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. [. . . ] Center Down Up ( Center ) ASPECT Select image aspect ratio: 4:3[ ] 16:9[ ] 4:3 small[ ] Select position of image: Press button while 16:9[ ]/4:3 small[ ] is selected. Center Down Up ( Center ) · 4:3 small may not be displayed correctly with some input signals. - - ENGLISH-12 OPERATIONS (continued) SETUP RGB VIDEO AUTO INPUT IMAGE fH:38kHz fV:60Hz OPT. The following functions are available when INPUT is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. Table 4. Input Menu Item RGB Description Displays RGB input frequency: Displays the horizontal and vertical sync signal frequency for RGB input. Select video signal type: Select the signal type with the and buttons. Select NTSC, PAL, SECAM, NTSC4. 43, M-PAL, or N-PAL as appropriate for the input signal. Auto Adjust is valid at VIDEO/S-VIDEO input when AUTO is selected, and is then used for automatic selection of the signal type. Horizontal position, vertical position, clock phase, and horizontal size are automatically adjusted when EXECUTE is selected. Automatic adjustment at VIDEO/S-VIDEO input: Select EXECUTE with the button. A signal type appropriate for the input signal is selected automatically when EXECUTE is selected. · This function is the same as for Auto Adjust in Basic operation. VIDEO AUTO ENGLISH-13 ENGLISH Input Menu OPERATIONS (continued) Image Menu The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start operation. SETUP INPUT IMAGE OPT. Image Menu Item KEYSTONE Description Adjustment: Reduce size of bottom of image Reduce size of top of image · When this function is activated, the image may not be displayed correctly with some input signals. · The image is cleared when the BLANK mode is set with BLANK ON, or when there is no signal, and the entire screen is displayed in the selected color. Select Mirror status: Select mirror status with and buttons. BLANK MIRROR START UP Operation start/stop: Press the or button. · Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal. ENGLISH-14 OPERATIONS (continued) SETUP INPUT IMAGE OPT. Select an item with the and buttons, and start operation. VOLUME MENU COLOR TIMER LANGUAGE AUTO OFF SYNC ON G Table 6. Options Menu Item VOLUME MENU COLOR TIMER Description Volume adjustment: Reduce VOLUME Increase VOLUME Select menu background color: Select with the Operation start/stop: Press the Setup initial timer value: Set 1~99 minutes with the and or button. and buttons. buttons. LANGUAGE Operation start/stop: Press the or button. Select menu display language: Select with the and buttons. AUTO OFF Operation start/stop: Press the or button. The system automatically enters the standby mode when no or unsuitable signal is received for the set time. When STOP is selected the system does not enter the standby mode even if no or unsuitable signal is received. · May not be displayed correctly with some input signals when SYNC ON G is valid. [. . . ] The horizontal or vertical frequency of the input signal is not within the specified range. · Is the ambient temperature in excess of 35°C? *1) CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIME. NO INPUT IS DETECTED ON *** SYNC IS OUT OF RANGE ON *** CHECK THE AIR FLOW NOTE: *1) This message is cleared automatically after approximately three minutes, and appears every time power is switched ON. ENGLISH-20 TROUBLESHOOTING (continued) The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Indicators Message POWER LAMP TEMP indicator indicator indicator Lights orange Blinks green Lights green Blinks orange Lights red Contents Turns off Turns off The Standby mode has been set. [. . . ]