User manual HITACHI CP-X1200WA

[. . . ] KEYSTONE LENS SHIFT BNG COMPONENT S-VIDEO VIDEO STANDBY/ON TEMP LAMP RGB M1-D INPUT SEARCH RESET MENU FOCUS ZOOM INTER CP-X1200W/CP-X1250W Projector PORTUGUÊS NEDERLANDS NORSK ITALANO ESPAÑOL DEUTSCH FRANÇAIS ENGLISH Projector CP-X1200W/CP-X1250W Thank you for purchasing this projector. WARNING Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. NOTE · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual. [. . . ] (This table is continued to the following page. ) MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT COLOR SPACE COMPONENT VIDEO 3D-YCS VIDEO NR P. POWERUP INPUT AUTO COMPONENT AUTO TURN OFF LOW VIDEO RGB COLOR SPACE COMPONENT VIDEO 3D-YCS VIDEO NR 27 Multifunctional Settings (continued) INPUT Menu (continued) Item Description Select a signal input port for the child window using the / buttons. : VIDEO S-VIDEO memo About the child window, please refer to the section "Displaying the Child Window". INPUT memo About the child window, please refer to the section "Displaying the Child Window". Select a signal input port to display just when the projector is turned on, using the / buttons. : LAST INPUT M1-D RGB BNC COMPONENT S-VIDEO VIDEO Selecting the LAST INPUT selects the port that was used at the last time. Pressing the (or the ENTER) button displays the INPUT INFORMATION menu. The INPUT INFORMATION menu shows the information about the current signal input as illustrated below. INPUT-INFORMATION RGB 1024x768 @60. 0 FRAME LOCK INPUT-INFORMATION S-VIDEO SECAM AUTO INPUT-INFORMATION COMPONENT 575i @50 SCART RGB POWERUP INPUT INFORMATION memo The "FRAME LOCK" message means the frame lock function is working. This function automatically works when a RGB signal with vertical frequency of 50 to 60 is input, and it displays a moving picture more smoothly. memo The "SCART RGB" message means the COMPONENT port is working as a SCART RGB port. : TURN ON TURN OFF When the TURN ON is selected, an S2-video signal can be identified and the optimum aspect ratio is automatically selected. memo When the ASPECT button is used or the item "ASPECT" of the MAIN menu is operated, the TURN OFF will be automatically selected to this item. : EXECUTE CANCEL The items of the INPUT menu are collectively returned to the initial setting. Note that the item "INFORMATION" is not reset. S2-ASPECT RESET 28 Multifunctional Settings (continued) AUTO Menu With the AUTO menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item Description Pressing the (or the ENTER) button performs the automatic adjustment. At a RGB signal The vertical position (V POSITION), the horizontal position (H POSITION), the clock phase (H PHASE) and the horizontal size (H SIZE) will be automatically adjusted. memo Make sure that the application window is set to its maximum size prior to attempting to use this feature. At a video signal The signal type mode best suited for the respective input signal will be selected automatically. memo This function is available only when the AUTO is selected to the item "VIDEO" of the INPUT menu. For a component video signal, the signal type is identified automatically independently of this function. memo This operation requires approximately 10 seconds, and the message "AUTO IN PROGRESS" is displayed during the operation. a irregular picture, a color lack), please select the suitable mode to the item "VIDEO" of the INPUT menu. [. . . ] Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low : Lower byte of CRC flag for command data CRC_high : Upper byte of CRC flag for command data 3. Command data Command Data Chart byte_0 low byte_1 high byte_2 Type low high byte_3 byte_4 low byte_5 high Action Setting code Action (byte_0 - 1) Action 1 2 4 5 6 SET GET INCREMENT DECREMENT EXECUTE Classification Content Change setting to desired value. Run a command. 7 RS-232CCommunication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (`02H'+`00H'+ type (2 bytes)+`00H'+`00H') from the computer to the projector. (2) The projector returns the response code `1DH'+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (`01H'+`00H'+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector. [. . . ]