User manual HITACHI CP-WX625

[. . . ] Projector CP-WX625 User's Manual (detailed) ­ Operating Guide Thank you for purchasing this projector. WARNING Before using this product, please read the "User's Manual Safety Guide" and related manuals to ensure the proper use of this product. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling. [. . . ] · This function will be unavailable when the Transition Detector is on (53). Shrink the top of the image ó Shrink the bottom of the image · The adjustable range of this function will vary among inputs. · When the horizontal lens shift is not set to the center, this function may not work well. · This function will be unavailable when the Transition Detector is on (53). AUTO KEYSTONE EXECUTE KEYSTONE (continued on next page) 36 SETUP Menu SETUP Menu (continued) Item Description Using the / buttons corrects the horizontal keystone distortion. Shrink the right of the image ó Shrink the left of the image · The adjustable range of this function will vary among inputs. · When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible. · When the vertical lens shift is not set fully upward (not set fully downward for the optional lens type FL-601 only (47)), this function may not work well. · This function will be unavailable when the Transition Detector is on (53). NORMAL ó WHISPER · When the WHISPER is selected, acoustic noise and screen brightness are reduced. Using the / buttons switches the mode for mirror status. KEYSTONE WHISPER MIRROR NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm (53) will be displayed when projector is restarted after the power switch is turned off. The combination of a picture shown on screen and output from the MONITOR OUT port can be arranged in the menu. The picture coming into the port selected in the (2) is output to the MONITOR OUT port while an image from the port chosen in the (1) is on screen. QUIT ó RGB1 ó RGB2 ó HDMI STANDBY ó VIDEO ó S-VIDEO ó COMPONENT(Y, CB/PB, CR/PR) · Choose STANDBY, to select the output signal from the MONITOR OUT port in the standby mode. · While QUIT is selected, pressing the button returns to the previous menu. RGB1 ó RGB2 ó OFF · OFF disables the MONITOR OUT port. MONITOR OUT (continued on next page) 37 AUDIO Menu From the AUDIO Menu, items shown in the table below can be performed. Select an item using the / cursor buttons on the projector or remote control, and press the cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. NOTE · The speaker sound may distorted or the case may be trembling when the volume is too high or treble/bass is emphasized or WOW is activated. In that case, make the volume reduced, bass/treble low or WOW effect to be weakend. Item VOLUME TREBLE BASS Description Using the / buttons adjusts the volume. High ó Low Using the / buttons switches the mode for SRS WOW mode. HIGH ó MID ó OFF · SRS WOW® accomplishes this by providing a panoramic threedimensional audio image that extends the sound field in both the horizontal and vertical planes, and lowers the perceived bass response well beyond the low frequency limitations of the drivers. TURN ON ó TURN OFF · When the TURN ON is selected the built-in speaker works. [. . . ] Change the audio setting in the AUDIO Menu. The digital audio in HDMI signal does not work well. Use the analogue audio, connecting either an RCA audio cable or stereo mini cable. The lens cover is attached. Remove the lens cover. The signal cables are not correctly connected. Correctly connect the connection cables. No pictures are displayed. The brightness is adjusted to an extremely low level. Adjust BRIGHTNESS to a higher level using the menu function or the remote control. The computer cannot detect the projector as a plug and play monitor. Make sure that the computer can detect a plug and play monitor using another plug and play monitor. 11 22 10 The BLANK screen is displayed. Correctly connect the HDMI cable. No pictures or disturbed pictures are displayed on HDMI input. Press the BLANK button on the remote control. The HDMI cable is not correctly connected. Your HDMI equipment is not compatible with the projector This projector can be connected with another equipment that has HDMI or DVI connector, but with some equipment the projector may not work properly. [. . . ]