User manual HITACHI CPS318

[. . . ] Liquid Crystal Projector CP-S318/CP-X328 (CP-S318W/CP-X328W) USER'S MANUAL Vol. 1 Basic Please read this user's manual thoroughly to ensure correct usage through understanding. ENGLISH STANDBY/ON INPUT KEYSTONE RESET LANP TENP POWER LCD Projector CP-S318/CP-X328 USER'S MANUAL Thank you for purchasing this projector. Vol. 1 (Basic) WARNING · Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual · The reproduction, transmission or use of this document or contents is not permitted without express written authority. [. . . ] Item selection : Choose an item using the button, and press the button or the ENTER button. Return menu to last previous screen: Press the button or the ESC button. Execution of settings and/or adjustments: Operate by using the button. (For further details, read the explanation for each separate menu. ) Initialization of settings and/or adjustments: During operation, press the RESET button. (Note that items whose functions are performed simultaneously with the operation of clock phase, language selection, automatic adjustment, etc. , cannot be initialized. ) End menu operations: Press the MENU button, or do not perform any operation for several seconds. MAIN Menu With the MAIN menu, the seven items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION BRIGHT CONTRAST ASPECT PICT. GAMMA MIRROR LANGUAGE 12 : SELECT MAIN Menu Item BRIGHT CONTRAST Adjust Brightness: Light Adjust Contrast: Strong Description Dark Weak Example : MAIN Menu (BRIGHT) ASPECT Select Aspect Ratio: At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT VIDEO Input: 4:3 16:9 At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input: 4:3 16:9 SMALL · The SMALL picture may not be displayed correctly with certain input signals. Select Picture Position (for 16:9/SMALL Picture): TOP CENTER BOTTOM Select Gamma Mode: NORMAL CINEMA Select Mirror Status: NORMAL H:INVERT Select Menu Language: ENGLISH FRANÇAIS ITALIANO NORSK POTUGUÊS DYNAMIC V:INVERT H&V:INVERT PICT. POSIT. GAMMA MIRROR LANGUAGE DEUTSCH ESPAÑOL NEDERLANDS 2 PICTURE 1 Menu With the PICTURE 1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT 12 : SELECT Example : PICTURE1 Menu (COLOR BAL R) PICTURE1 Menu Item COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT Description Adjust Red Color Balance: Dark Adjust Blue Color Balance: Dark Adjust Sharpness (for VIDEO/S-VIDEO): Clear Adjust COLOR (for VIDEO/S-VIDEO/COMPONENT VIDEO): Dark Light Adjust Tint (for VIDEO/S-VIDEO): Green Red Light Light Soft PICTURE 2 Menu With the PICTURE 2 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION V POSITION H POSITION H PHASE H SIZE OVER SCAN 12 : SELECT Example : PICTURE2 Menu (V POSITION) PICTURE2 Menu Item V POSITION H POSITION H PHASE Description Adjust Vertical Position (for RGB): Up Adjust Horizontal Position (for RGB): Left Down Right Adjust Horizontal Phase (for RGB/COMPONENT VIDEO): Right Left · Adjust to eliminate flicker. Adjust Horizontal Size (for RGB): Large Small · If the horizontal size adjustment is excessive, the image may not be displayed correctly. Select Over-scan Ratio (for VIDEO/S-VIDEO/COMPONENT VIDEO): LARGE MIDDLE SMALL · It is recommended to select SMALL to avoid flicker at the lower part of the picture. H SIZE OVER SCAN 3 MULTIFUNCTIONAL SETTINGS (continued) INPUT Menu With the INPUT menu, the four items shown in the Table below can be performed. With inputting of RGB IN 1 and RGB IN 2 signals, the horizontal and vertical frequencies of the signals will be displayed on the initial screen of the INPUT menu. Perform each operation in accordance with the instructions in the Table. MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION AUTO VIDEO HDTV SYNC ON G EXECUTE : SELECT Example : INPUT Menu (AUTO) INPUT Menu Item Description Auto Adjust (for RGB): Automatically adjusts H POSITION, V POSITION, H PHASE, and H SIZE. Auto Adjust (for VIDEO/S-VIDEO): Automatically selects the proper VIDEO mode for the current input signal. This function is active only when the AUTO mode is selected for the item VIDEO. · This function may not be available with a PAL60 signal and certain other signals. · For COMPONENT VIDEO, the signal type is identified automatically even if this function is inactive. Select Mode of Signal Type (for VIDEO/S-VIDEO): AUTO NTSC PAL SECAM NTSC4. 43 M-PAL N-PAL Selecting AUTO mode activates and performs the AUTO function for VIDEO/SVIDEO. The image becomes irregular, or lacks color. ) · AUTO mode may not function correctly with a PAL60 signal and certain other signals. · For COMPONENT VIDEO, the signal type is identified automatically even if this function is inactive. [. . . ] (3) The projector returns the response code `06H' to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data (`05H'+`00H'+ type (2 bytes) +`00H' + `00H') to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code `06H' to the computer. When a command sent by the projector cannot be understood by the computer When the command sent by the projector cannot be understood, the error command `15H' is returned by the computer. Some times, the projector ignores RS-232C commands during other works. [. . . ]