User manual HITACHI CP-S245

[. . . ] Projector CP-S245/CP-X255 User's Manual ­ Operating Guide Thank you for purchasing this projector. WARNING Before using this product, please read the "User's Manual Safety Guide" and related manuals to ensure the proper use of this product. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling. [. . . ] Left Right · Over-adjusting the horizontal position may cause noise to appear on the screen. If this occurs please reset the horizontal position to the default setting. Pressing the RESET button when H POSITION is selected will reset the H POSITION to the default setting. Using the buttons / adjusts the horizontal phase to eliminate flicker. Right Left · This item can be selected only for an RGB signal or a component video signal. Note that this does not work with the input signal of 525i(480i)/625i(576i)/SCART RGB from the component video port. MENU[RGB] PICTURE IMAGE INPUT SETUP SCREEN OPTION NETWORK EASYMENU :SELECT ASPECT4:3 OVERSCAN5 VPOSITION25 HPOSITION142 HPHASE16 HSIZE1344 AUTOADJUSTEXECUTE OVER SCAN V POSITION H POSITION H PHASE 30 Multifunctional settings IMAGE Menu (continued) Item Description Using the buttons / adjusts the horizontal size. Large Small · This item can be selected only for an RGB signal. · When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please reset the adjustment by pressing the RESET button on the remote control during this operation. For an RGB signal The vertical position, the horizontal position, the clock phase and the horizontal size will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. For a video signal or s-video signal The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the VIDEO FORMAT item in the INPUT menu. For a component video signal, the signal type is identified automatically independently of this function. For a video signal, s-video signal or component video signal The vertical position and horizontal position will be automatically adjusted. For a component video signal The aspect ratio will be automatically selected. · The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function correctly with some input. H SIZE AUTO ADJUST EXECUTE 31 Multifunctional settings INPUT Menu With the INPUT menu, the items shown in the table below can be performed. Select an item using the cursor buttons / on the projector or remote control, and press the cursor button on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it referring to the following table. Item Description Using the buttons / switches the mode for color space. AUTO RGB SMPTE240 REC709 REC601 COLOR SPACE · This item can be selected only for an RGB signal or a component video signal (except signals of 525i(480i)/625i(576i)/SCART RGB from the component video port). In such a case, it might be good to select a suitable mode except AUTO. [. . . ] After the remedy, reset the power to ON. There is a possibility that the interior portion has become heated. It is time to clean the air filter. Lighting In Green Simultaneous blinking in Red Blinking in Green for approx. 3 seconds Turned off Turned off At least 1 "Power ON" schedule is saved to the projector. (Please refer to the User's Manual-Network Functions: Schedule Settings for more information. ) NOTE · When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the "" (OFF) side of the power switch, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again. 51 Troubleshooting Phenomena that may be easy to be mistaken for machine defects WARNING Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. [. . . ]