User manual HITACHI CPL540E

[. . . ] · The reproduction, transmission or use of this document or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGMENT : · VGA and XGA are registered trademarks of the International Business Machines Corporation. · Apple and Mac are registered trademarks of Apple Computer, Inc. · VESA and SVGA are trademarks of the Video Electronics Standard Association. [. . . ] · When this function performs, the VIDEO NR function is ineffective. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION : SELECT COLOR SPACE COMPONENT VIDEO FRAME LOCK 3D-YCS VIDEO NR PROGRESSIVE INFORMATION AUTO COMPONENT AUTO TURN ON NORMAL LOW TURN OFF COLOR SPACE COMPONENT VIDEO FRAME LOCK 3D-YCS 27 Multifunctional Settings (continued) INPUT Menu (continued) Item Description Select a Noise Reduction Mode: HIGH MIDDLE LOW · This function performs only at a VIDEO input or a S-VIDEO input. At a VIDEO input of NTSC 3. 58, this function performs only when the TURN OFF is selected under the 3D-YCS. · When the HIGH, the MIDDLE or the LOW is selected, the noise on screen is reduced according to each mode. · When this function is excessive, it may cause a certain degradation of the picture. Select the Progressive Mode: TV FILM TURN OFF · This function performs only at an interlaced signal of a VIDEO input, a SVIDEO input or a COMPONENT VIDEO input of 525i or 625i signal. The FILM mode is adaptable to the 3-2 Pull-Down system to the conversion. · When the TV or FILM is selected, the screen image will be crisper. But it may cause a certain defect (for example, jagged line) of the picture at a quick moving object. In such a case, please select the TURN OFF, even though the screen image may lose the crisp. · This function may cause a certain degradation of the picture. Display the Information: Pressing the or the ENTER button performs this function. Reset the AUTO Menu Items: Selecting the EXECUTE performs this function. EXECUTE CANCEL · The items of the AUTO menu are collectively returned to the initial setting. Note that the item ADJUST is not reset. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION : SELECT ADJUST POWER OFF SEARCH RESET 0 min TURN ON ADJUST POWER OFF SEARCH RESET 29 Multifunctional Settings (continued) SCREEN Menu With the SCREEN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item Description Select a Blank Screen Color: BLUE WHITE BLACK · The blank screen of selected color is displayed by pressing the BLANK button. Please refer to the section "Temporarily Blanking The Screen" of "Operating" about the screen blanking. Select the Start Up Screen: TURN ON TURN OFF · If the TURN ON is selected when there is no signal or the detected signal is out of specifications, the blank screen is displayed. Adjust a Menu Position: Pressing the or ENTER button start adjusting, Up MENU POSITION Left Right MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION : SELECT BLACK BLANK TURN ON START UP MENU POSITION MESSAGE TURN ON RESET BLANK START UP Down · The button does not finish this item. When you want to return to the previous display, please press the ESC button. Select the Message Mode: TURN ON TURN OFF · When the TURN OFF is selected, the following message functions are disabled: The message of "AUTO IN PROGRESS" The message of "NO INPUT IS DETECTED" The message of "SYNC IS OUT OF RANGE" The message while being searched for an input signal, "Searching . . . . . " The message when an input signal is detected, "Detecting . . . . . " The indication of the input signal by input change. Reset the SCREEN Menu Items: Selecting the EXECUTE performs this function. EXECUTE CANCEL · The items of the SCREEN menu are collectively returned to the initial setting. MESSAGE RESET 30 Multifunctional Settings (continued) OPTION Menu With the OPTION menu, the items shown in the table below can be performed. [. . . ] Wait until the POWER indicator has finished flashing, and then perform the proper response measure using the item descriptions below as reference. The projector lamp has not been properly fixed (attached), the projector lamp does not light, and/or there is a possibility that the interior portion has become heated. After the unit has sufficiently cooled down, please make confirmation of the following items, Lighting in Turned off and then turn the power ON again. After the unit has Blinking in Turned off sufficiently cooled down, please make confirmation of the red attachment state of the lamp and lamp cover, and then turn the power ON again. Lighting or blinking in red Lighting or blinking in red 40 Troubleshooting (continued) Regarding The Indicator Lamps (continued) POWER indicator Lighting or blinking in red LAMP indicator TEMP indicator Description Turned off The cooling fan is not operating. [. . . ]