User manual HITACHI CPL500A

[. . . ] If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferable a qualified electrician. [. . . ] · Do not revolve the foot adjusters by force, the foot adjusters is damaged. · Do not apply unnecessary force from the upper side when lifting the projector. Otherwise, projector may be damaged or a finger could be caught and cause injury. 12 Basic operations To project the picture 2 STANDBY/ON MAGNIFY VOLUME INPUT 3 OFF POSITION ON LASER MUTE MENU 7 RESET MENU ON RIGHT MOUSE ON TIMER VIDEO INPUT RESET 5 7 1 BLANK RGB 1 2 3 4 5 6 7 Turn the MAIN POWER switch of the projector on. [ I : ON] · The ON indicator will light up orange. Press the STANDBY/ON button. · The ON indicator blinks (green) during warm-up and then lights (green). · Power cannot be turned on even if the STANDBY/ON button is pressed within 60 seconds after power is turned off, since the lamp has cooled preparing for next lighting. Remove the lens cap. Power on all connected equipment. The method of connecting various equipment, see on the page 20~28. Press the INPUT button or the INPUT SELECT (VIDEO or RGB) button to select the source of the signal to be projected on the screen. Example on-screen display · The selected signal input is displayed at the bottom right of the screen for 3 seconds. RGB1 13 ENGLISH 4 2 STANDBY/ON MUTE FREEZE Basic operations (continued) To turn off the power 1 STANDBY/ON 1 INPUT STANDBY/ON MUTE FREEZE MAGNIFY VOLUME OFF 3 MUTE POSITION ON LASER MENU RESET RESET MENU ON BLANK RGB INPUT RIGHT MOUSE ON TIMER VIDEO 2 1 2 3 Press the STANDBY/ON button, for 1 second. · The ON indicator blinks orange and the lamp turns off. (About 1 minute later), the fan stops and the indicator lights up orange. · Press the STANDBY/ON button for short time (less than 1 second), the projector do not set in standby mode. Turn the MAIN POWER switch of the projector off. [ Install the lens cap. : OFF] Caution · To reduce temperature inside the projector, fan will rotate for about 1 minute after the lamp is turned off. · Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged. PLUG&PLAY This projector complies with VESA DDC1/2B specifications. PLUG&PLAY is a system with computer, peripherals (including projectors), and operating system. It works when the projector is connected to DDC (Display Data Channel) ready computer that is running an operating system software that incorporates plug & play functionality. (Please refer to the above table. ) < Manual Operation > Adjust optional items manually. (1) Use the MENU buttons on the unit or the DISK PAD on the remote control to move the green cursor to the number of the item you wish to adjust. (2) With the green cursor on the number, use the MENU buttons on the unit or the DISK PAD on the remote control to raise or lower the value. SETUP INPUT IMAGE OPT. VOLUME BRIGHT CONTRAST V POSIT H POSIT H PHASE H SIZE COLOR BAL 121 57 7 800 R AUTO B 17 ENGLISH Adjustments and functions (continued) < AUTO-adjustment > The projector will automatically adjust four items (V POSIT, H POSIT, H PHASE, H SIZE, White level). When AUTO is selected (the cursor is moved from Manual Operation towards the right) the AUTO Confirm screen shown below will be displayed. < AUTO-adjustment Confirm Screen > While the AUTO confirmation screen is displayed as illustrated on the upper right, if you shift the cursor upward and select AUTO, the projector will perform auto-adjustment. If CANCEL is selected for three seconds, or if the RESET button on either the unit or the remote control is pressed, the green cursor will return to the value for the selected item (Manual Operation) SETUP INPUT IMAGE OPT. VOLUME BRIGHT CONTRAST 123 V POSIT AUTO 111 H POSIT CANCEL 31 H PHASE 1024 H SIZE R COLOR BAL AUTO B < During AUTO-adjustment > At the lower right of the screen the word <AUTO> will flash in green letters. When the auto-adjustment is completed the word <AUTO> will disappear. The auto-adjustment of the white level is cancelled by input switching and signal mode change. Caution AUTO · When start up screen is displayed ("NO INPUT IS DETECTED" or "SYNC IS OUT OF RANGE" is displayed), SETUP menu items other than VOLUME cannot be set. · TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input. · V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted with a VIDEO signal input. · Auto-adjustment will take about 10 to 15 seconds to complete. [. . . ] (See page 21, 22) *1 This message are not displayed after 3 minutes. *2 It is possible to again turn on the power, however the power will go off after about 10 minutes. Indicator display The ON indicator, LAMP indicator and TEMP indicator will light or blink in the following cases. ON indicator Lights orange Blinks green Lights green Blinks orange Lights red LAMP indicator TEMP indicator Goes off Goes off Goes off Goes off Lights red Goes off Goes off Goes off Goes off Goes off Meaning Standby mode During warming up During operation *1 During cooling down Lamp cannot light *2 Cool projector by power off for 45 minutes. Remedy Lights red Lights red Blinks red Blinks red Goes off Blinks red Goes off Blinks red Goes off Lamp is not inserted or the Securely insert the lamp or close the lamp door open lamp door. Cooling fan accidented Accumulated lamp operation time has exceeded 2, 000 hours Call a maintenance person. [. . . ]