User manual HITACHI CP-X4015WN

[. . . ] € Automatic adjustment may not function correctly with some input signals. € The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G. 1 Initial set signals Initial set signals The following signals are used for the initial settings. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. [. . . ] For details of RS-232C commands, refer to RS-232C Communication / Network command table ( 17). NOTE • If data is transferred via wireless and wired LAN at the same time, the projector may not be able to process the data correctly. If you use wired LAN, connect the projector's LAN port to the computer's 2. If you use wireless LAN, insert the USB wireless adapter into the projector's USB TYPE A port. Turn the computer on, and after the computer has started up turn the projector on. LAN cable (CAT-5 or greater) LAN LAN 11 Command Control via the Network (continued) Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items form a web browser when command control is used. Port Settings Port open Network Control Port1 (Port: 23) Authentication Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23. Click the [Enable] check box for the [Authentication] setting when authentication is required. Click the [Enable] check box to open [Network Control Port2 (Port: 9715)] to use TCP #9715. Click the [Enable] check box for the [Authentication] setting when authentication is required. Port open Network Control Port2 (Port: 9715) Authentication When the authentication setting is enabled, the following settings are required. Security Settings Authentication Password Network Control Re-enter Authentication Password Enter the desired authentication password. ConfirmThis setting will be the same for [Network Control Port1 (Port: 23)] and [Network Control Port2 (Port: 9715)]. Command format Same as RS-232C communication, refer to RS-232C Communicaton command format. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4). (5) Authentication error reply : 1Fh + 0400h When authentication error occurred, the projector returns the error code. Command format The commands some datum are added to the head and the end of the ones of TCP#9715 are used. Header 0×02 Data length 0×0D RS-232C command 13 bytes Check sum 1 byte Connection ID 1 byte [Header] 02, Fixed [Data Length] RS-232C commands byte length (0×0D, Fixed) [RS-232C commands] Refer to RS-232C Communication command format ( 9). [Check Sum] This is the value to make zero on the addition of the lower 8 bits from the header to the checksum. [Connection ID] Random value from 0 to 255 (This value is attached to the reply data). NOTE • Operation cannot be guaranteed when the projector receives an undefined command or data. [. . . ] To use PJLinkTM without authentication, do not set any password in Web Browser Control. € For specifications of PJLinkTM, see the web site of the Japan Business Machine and Information System Industries Association. 0 (1280 x 768) (±10%) c2 Screen height cm 5 6 8 9 11 12 14 15 18 23 30 38 46 a Screen size (diagonal) type (inch) 30 40 50 60 70 80 90 100 120 150 200 250 300 16 : 9 screen b c1 Projection distance Screen height min. 6 39 15 51 20 64 25 77 30 90 35 103 41 116 46 129 51 154 61 193 76 257 101 322 127 386 152 19 ENGLISH a Screen size (diagonal) c2 Screen height c2 T-3 CP-WX2515WN, CP-WX3015WN 16 : 10 screen b c1 Projection distance Screen height min. [. . . ]