User manual HITACHI CP-X325

[. . . ] Liquid Crystal Projector ENGLISH USER'S MANUAL Thank you for purchasing this liquid crystal projector. Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE: · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual · The reproduction, transmission or use of this documents or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGMENT: · PS/2, VGA and XGA are registered trademark of International Business Machines Corporation. [. . . ] In such cases, remove the signal connector so that knows signal is received, set SYNC ON G to invalid, and reconnect the signal. SYNC ON G ENGLISH-15 ENGLISH Options Menu OPERATIONS (continued) No Signal Menu The same adjustments and settings are available as with the Image and Options menus when the MENU button is pressed during display of the "NO INPUT IS DETECTED ON ***" or "SYNC IS OUT OF RANGE ON ***" message while no signal is received. VOLUME KEYSTONE BLANK MIRROR START UP MENU COLOR TIMER LANGUAGE AUTO OFF SYNC ON G 40 +1 Table 7. No Signal Menu Item VOLUME KEYSTONE Description Volume adjustment: Reduce VOLUME Adjustment: Reduce size of bottom of image Increase VOLUME Reduce size of top of image Select blank screen color: Select color with the BLANK and buttons. · When the blank mode is set with BLANK ON, by absence of a signal, or by input of a non-standard signal, the image is cleared and the complete screen is displayed in the selected colour. Note that if No Display is selected in Initial Screen the blank screen is displayed in blue when no signal is received. MIRROR Operation start/stop: Press the or button. Select Mirror status: Select mirror status with and buttons. START UP Operation start/stop: Press the or button. · Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal. Select menu background color: Select with the Operation start/stop: Press the or button. Setup initial timer value: Set 1~99 minutes with the Operation start/stop: Press the or button. buttons. MENU COLOR TIMER LANGUAGE AUTO OFF Operation start/stop: Press the or button. The system automatically enters the standby mode when a signal is not received for the set time. When STOP is selected the system does not enter the standby mode even if no signal is received. SYNC ON G invalid: Select TURN OFF with the button. · May not be displayed correctly with some input signals when SYNC ON G is valid. In such cases, remove the signal connector so that knows signal is received, set SYNC ON G to invalid, and reconnect the signal. SYNC ON G ENGLISH-16 MAINTENANCE HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Contact your dealer before replacing the lamp. (Option lamp: DT00331) Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high temperatures. WARNING · For disposal of used lamp, treat according to the instruction of Lamp community authorities. · Since the lamp is made of glass, do not apply shock to it and do not scratch it. · If it is probable that the lamp has exploded (explosive sound is heard), disconnect the power plug from the power outlet and ask Reflector Front your dealer to replace lamp. glasss The lamp is covered by front glass , but, in rare cases, the reflector and the inside of the projector may be damaged by scattered broken pieces of glass, and broken pieces could cause injury when being handled. · Do not use the projector with the lamp cover removed. Lamp Life Projector lamps have a finite life. The image will become darker, and hues will become weaker, after a lamp has been used for a long period of time. Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message (see P. 20 Table 8) appears when the projector is switched ON. NOTE: The LAMP is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. [. . . ] (2) The projector returns the response code `1DH'+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (`01H'+`00H'+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code `06H' to the computer. Using the projector default settings (Reset Command) (1) The computer sends the default setting code Header + Command data (`06H'+`00H'+ type (2 bytes) +`00H'+`00H') to the projector. (3) The projector returns the response code `06H' to the computer. Increasing the projector setting value (Increment command) (1) The computer sends the increment code Header + Command data (`04H'+`00H'+ type (2 bytes) +`00H'+`00H') to the projector. [. . . ]