User manual HITACHI CP-A100

[. . . ] Projector CP-A100 User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING Before using this product, please read all manuals for this product. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling. [. . . ] When the registration is completed, the registered screen and the following message are displayed for several seconds: "MyScreen registration is finished. " If the registration failed, the following message is displayed: "A capturing error has occurred. Please try again. " · This function cannot be selected when the TURN ON is selected to the MyScreen Lock item (below). · This function cannot be selected when TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION Menu (48). TURN ON ó TURN OFF When the TURN ON is selected, the MyScreen item is locked. · This function cannot be selected when TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION Menu (48). MyScreen MyScreen Lock (continued on next page) 40 SCREEN Menu SCREEN Menu (continued) Item Description Using the / buttons turns on/off the message function. TURN ON ó TURN OFF When the TURN ON is selected, the following message function works. "AUTO IN PROGRESS" while automatically adjusting "NO INPUT IS DETECTED" "SYNC IS OUT OF RANGE" "Searching. . . " while searching for the input "Detecting. . . " while an input signal is detected The indication of the input signal displayed by changing The indication of the aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the MY MEMORY displayed by changing The indication of "FREEZE" and "II" while the projector is in the FREEZE mode. · If the projector goes into the FREEZE mode while the TURN OFF is selected, the picture on screen is frozen without any messages, which is not a malfunction (23). (1) Use the / buttons on the SCREEN Menu to select SOURCE NAME and press the button. (2) Use the / buttons on the SOURCE NAME menu to select the port to be named and press the button. Use the /// buttons and the ENTER or INPUT button to select and enter characters. Also if you move the cursor to DELETE or ALL CLEAR on screen and push the ENTER or INPUT button, 1 character or all characters will be erased. (4) To change an already inserted character, press the () button to move the cursor to the first line, and use the / buttons to move the cursor on the character to be changed. (5) To finish entering text, move the cursor to the SAVE on screen and press the ENTER or INPUT button. To revert to the previous name without saving changes, move the cursor to the CANCEL on screen and press the ENTER or INPUT button. 4 MESSAGE SOURCE NAME OPTION Menu OPTION Menu From the OPTION Menu, items shown in the table below can be performed. Select an item using the / cursor buttons, and press the cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table. Item Description Using the / buttons turns on/off the automatic signal search function. TURN ON ó TURN OFF When the TURN ON is selected, detecting no signal automatically cycles through input ports in the following order. Then when an input is found, the projector will stop searching and display the image. COMPUTER IN1 ð COMPUTER IN2 VIDEO S-VIDEO COMPONENT Using the / buttons turns on/off the AUTO ON function. TURN ON ó TURN OFF When set to the TURN ON, the lamp in projector will be automatically turned on without the usual procedure (16), only when the projector is supplied with the power after the power was cut while the lamp was on. [. . . ] In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again. Shutting the projector down Only when the projector can not be turned off by usual procedure (17), please push the shutdown switch using a pin or similar, and disconnect the power plug from the power outlet. Before turning it on again, wait at least 10 minutes to make the projector cool down enough. Shutdown switch MONITOR OUT Resetting all settings When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION Menu (46) can reset all settings(except LANGUAGE, FILTER TIME, LAMP TIME, FILTER MESSAGE, NETWORK settings and etc. ) to the factory default. 70 Troubleshooting Phenomena that may be easy to be mistaken for machine defects About the phenomenon confused with a machine defect, check and cope with it according to the following table. Phenomenon Cases not involving a machine defect Reference page The electrical power cord is not plugged in. Correctly connect the power cord. The main power source has been interrupted during operation such as by a power outage (blackout), etc. Power does not come on. Please disconnect the power plug from the power outlet, and allow the projector to cool down at least 10 minutes, then turn the power on again. 12, 16 Either there is no lamp and/or lamp cover, or either of these has not been properly fixed. Please turn the power off and disconnect the power plug from the power outlet, and allow the projector to cool down at least 45 minutes. [. . . ]