User manual HITACHI CMP4121HDU

[. . . ] Brisbane, Ca 94005-1835, U. S. A Tel:+1-800-HITACHI Fax:+1-650-244-7525 Hitachi Australia Ltd. 2113 Tel:+61(02)9888-4100 Fax:+61(02)9888-4144 Hitachi Home Electronics Asia (S)Pte. 16 Collyer Quay, #20-00 Hitachi Tower, Singapore 049318 Tel:(65)6536-2520 Fax:(65)6536-2521 HITACHI (HONG KONG) LIMITED 18/F. , Ever Gain Centre, 28 On Muk Street, Shatin, N. T. Tel:(852)2113 8883 Fax:(852)2780 4178 QR54121 Printed in Japan Color Plasma Display Monitor USER'S MANUAL MANUEL UTILISATEUR READ THE INSTRUCTIONS INSIDE CAREFULLY. [. . . ] Input can be switched in the sequence of RGB1 RGB2 VIDEO 1 VIDEO 2 by pressing the INPUT SELECT button of the monitor. Adjustment status guide display (The display color will change to pink. ) · When a button is pressed, the word MUTE (in pink) and the volume adjustment status guide will be displayed. · The volume setting can be lowered by pressing the VOL- button while the audio is muted. · The muting can be cancelled by pressing the VOL+ button while the audio is muted. When INPUT SELECT is pressed: RGB1 RGB2 VIDEO1 VIDEO2 (D-sub input) (D-sub input) (composite or S input) (component input) · When audio is muted with the on-screen display system, the volume setting can be adjusted. When the MUTE button of the remote control is pressed again, muting will be canceled, the volume display (blue) will appear and sound will be output. · If the video unit is not installed, you cannot switch to VIDEO1 and VIDEO2. · When the same signal is input to RGB1 and RGB2, the phases may be slightly misaligned. In such case, please change one refresh rate (Vertical frequency ) of the apparatus to be used. ENGLISH OPERATING INSTRUCTIONS (continued) Displaying Two Screens If the PinP button on the remote control is pressed when the optional video unit is installed, two screens will display. Activating the P-in-P mode from the RGB input screen Pressing the PinP button one time will display two screens. The speaker icon can be shifted left and right by pressing the and SELECT buttons; the audio of the video will be output from the R1 V1 side on which the speaker icon is located. The sub-screen can be selected with the VIDEO1 and VIDEO2 buttons from the status shown in the (Subdiagram to the right. screen) Pressing the PinP button again will cancel the two screen display. V1: Displays the VIDEO input signal of the sub-screen. VOL RECALL button SIZE button PinP button AUTO PinP MUTE VOL RECALL button Activating the P-in-P mode from the video input screen Pressing the PinP button one time will display two screens. · The speaker icon can be shifted left and right by pressing the and SELECT buttons; the audio of the video will be output from the side on which the speaker icon is located. · Pressing the PinP button again will increase the size of the screen. · Pressing the PinP button once again will cancel the two screen display. V1 V2 SIZE RECALL SIZE button RGB 1 RGB 2 VIDEO 1 VIDEO 2 MENU RETURN ENTER ID ID SET Refer to two screen table Size Switching Each time the SIZE button of the remote control or the monitor is pressed, the screen display size (or display area) will change in sequence and the status will be displayed at the bottom of the screen. · During RGB signal input TIPS Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the two screen display, the mode will not change to power save mode. Please be careful since image retention will occur if display is left in a two screen display state for a long period of time. NORMAL * REAL FULL ZOOM1 Input Signal Screen Display The input signal status can be displayed on the screen by pressing the RECALL button of the remote control. The display will go out in approximately 3 seconds. VIDEO VIDEO2 [COMPONENT] ZOOM3 ZOOM2 · Some types of signals may not be able to switch as desired. * VGA and W-VGA only · During VIDEO signal input (when the optional video unit is attached) 4:3 PANORAMA FULL MOVIE1 MOVIE2 Input terminal name RGB · Depending on the type of signal, in some cases it may not be possible to switch the size, or switching to some sizes may not be possible. RGB1 [RGB] <<FULL>> H : 46. 5kHz V : 60Hz Input horizontal frequency Input vertical frequency OPERATING INSTRUCTIONS (continued) ENGLISH VOL Using the Menu Screen (On-screen display system) When the MENU button is pressed, the adjustment menu screen will be displayed; from there, video adjustment and setting is possible by using the SELECT button, ADJUST button and ENTER button. SELECT/ADJUST buttons ID SET MUTE VOL AUTO PinP SIZE RECALL AUTO button RGB 1 RGB 2 VIDEO 1 VIDEO 2 MENU button MENU RETURN · Refer to settings. - concerning the adjustment items and the ENTER Example: Selecting the Picture screen ID ID button ENTER button ID SET button 1. Press the MENU button to display the Main Menu screen. MENU MAIN MENU PICTURE SOUND DISPLAY FUNCTION OTHER Automatic Adjustment of Screen Position and the Clock Adjustment of the screen to a position suitable for the video and the clock adjustment can be performed automatically by pressing the AUTO button of the remote control. SEL. (Use the and SELECT buttons to select other items. ) ENTER PICTURE MENU OPERATE MODE CONTRAST BRIGHTNESS COLOR TINT ENHANCER FILTER RESET SEL. : : : : : : : 1/2 NORMAL 127 0 0 0 LOW OFF CAUTIONS Perform this adjustment for each input (RGB1 or RGB2) and for each signal. * Depending on the signal, satisfactory adjustment may not be possible in some cases. In such case, adjust by referring to the Display Menu item. RTN BACK 3. Use the and SELECT buttons to select the item to be adjusted and then use the and ADJUST buttons to adjust (example: COLOR). Independent Operation of Multiple Monitors (ID No) Setting the ID No. of the remote control allows separate control of up to a maximum of seven monitors. The number will be incremented (2 6 7 1 2) when this button pressed continuously. The remote control ID no. can be checked by pressing the ID SET button while holding down the ID button. SET. ID:1 COLOR 0 ADJ RTN BACK · Press the RETURN button to return to the previous screen. [. . . ] · The thicknesses of characters and lines may vary if images with a vertical resolution greater than 512 lines are displayed; however, this is not a malfunction. - - · Coarse horizontal stripes appear in FULL display. - · The display dims to make the picture invisible during special playback of a VCR (FF, REW). · Flickering in the form of horizontal lines oscillating up and down. (PC INPUT MODE only) - · The fan motor is noisy. - · The top of the monitor heats up. - · Text characters are displayed with varying thicknesses. - TROUBLESHOOTING (continued) ENGLISH Actions to Correct Abnormal Displays Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the adjustments suggested below. Symptom 1 Text displayed across the screen appears vertically streaked, with some characters blurred (figure 1). [. . . ]