User manual HITACHI CM-P5000WXJ

[. . . ] Color Plasma Display Monitor Model CMP5000WXU CMP5000WXJ USER'S MANUAL MANUEL UTILISATEUR READ THE INSTRUCTIONS INSIDE CAREFULLY. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. Contents related to system specifications, power requirements, accessories, and other information differ with respect to the country where this unit is purchased. or Canada, please use and refer to the instructions written in either English or French. For customers in Japan, please use and refer to the instructions written in Japanese. [. . . ] If the polarity is reversed, the sound will be unnatural and lack bass. On-screen setup is necessary after connection. When connecting to INPUT2 (ON SYNC) Making connections to the audio inputs on this unit This unit features two audio inputs and one audio output. The following chart shows the video inputs and the corresponding audio input jacks. Video input INPUT1 Stereo mini jack (L/R) INPUT2 Audio input jacks Sound output Sound of the selected video input is output from the · SPEAKER terminals · Stereo mini jacks (L/R). G B INPUT2 (H/V SYNC) R HD VD 75Ô 2. 2 k Audio connections for component (computer) connected to INPUT 1 or INPUT 2 VD 75Ô 2. 2 k AUDIO INPUT OUTPUT (INPUT1/2) When using INPUT2, set the impedance selector switch to match the output impedance of the connected computer's synchronization signal. When the output impedance of the computer's synchronization signal is below 75 , set this switch to the 75 position. Please see pages 14 and 15. Notes ÷ When making composite SYNC connections, do not connect anything to the VD jack. ÷ On some types of Macintosh® components, G ON SYNC and composite SYNC are both output. With this type of component, please connect using the G ON SYNC connection (see page 10). Audio input to the AUDIO INPUT jacks (stereo mini jack) is possible for a component connected to either INPUT1 or INPUT2. Sound is output from both the AUDIO OUTPUT jacks (stereo mini jack) and the SPEAKER terminals according to the video input selection. 11 En Installation and Connections English Installation and Connections English Power Cord Connection Connect the power cord after all component connections have been completed. 1 2 1 2 Connect the power cord to this unit. Plug the power cord into a power outlet. ÷ Use only the power cord provided. ÷ Do not use a power supply voltage other than that indicated (AC 100 - 120 V, 50/60 Hz) as this may cause fire or electric shock. CAUTION Installation and Connections ÷ For the plasma display, a three-core power cord with a ground terminal is used for efficiency protection. Always be sure to connect the power cord to a three-pronged grounded outlet and make sure that the cord is properly grounded. If you use a power source converter plug, use an outlet with a ground terminal and screw down the ground line. 12 En Installation and Connections English * As viewed from the rear of the display. How to Route Cables Speed clamps and bead bands are included with this unit for bunching cables together. Once components are connected, follow the following steps to route cables. 1 2 1 Note Cables can be routed to the right or left. Speed clamps are designed to be difficult to undo once in place. Please attach carefully. To attach the speed clamps to the main unit Connect the speed clamps using the 4 holes marked with · below, depending on the situation. To remove speed clamps Using pliers, twist the clamp 90° and pull it outward. In some cases the clamp may have deteriorated over time and may be damaged when removed. 13 En Installation and Connections Organize cables together using the provided speed clamps. Insert 1 into an appropriate hole on the rear of the unit, then snap 2 into the back of 1 to fix the clamp. 2 Bunch separated cables together and secure them with the provided bead bands. Setting Up the System English Setup after Connection After components have been connected to INPUT1 or INPUT2, on-screen setup is necessary. Follow the procedure described below and make settings as they apply to the type of components connected. 6 Press 5/ to select SETTING, then press SET. MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L AMP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : AU T O : V GA Screen Mode setup Note These settings are required only when using the following input signal refresh rates: 1 31. 5 kHz horizontal / 60 Hz vertical; 2 48. 4 kHz horizontal / 60 Hz vertical, or 56. 5 kHz horizontal / 70 Hz vertical. No manual setup is necessary for signals with other refresh rates, since adjustments are performed automatically (the SETTING item will not be displayed). SELECT SET ENTER MENU EXIT 7 Press 2/3 to select the display mode. 1 Switch MAIN POWER on the connection panel to the on position to turn on the unit's main power. The menu screen appears. MAIN MENU SCREEN : CO NT RA S T 0 : BR I GHT . E NH AN CE 0 RE S E T PICTURE SET UP INPUT1 OPTION 2 S E T T I N G : V GA SELECT SET SET MENU EXIT 3 4 Setting Up the System 1 When the input signal has a refresh rate of 31. 5 kHz (horizontal) and 60 Hz (vertical), pressing 2/3 will cause the display mode to change alternately as follows: VGA WIDE VGA 2 When the input signal has a refresh rate of 48. 4 kHz horizontal / 60 Hz vertical, or 56. 5 kHz horizontal / 70 Hz vertical, pressing 2/3 will cause the display mode to change alternately as follows: XGA WIDE XGA SELECT SET ENTER MENU EXIT 8 5 Press 2/3 to select SET UP. MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L AMP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : AU T O : V GA When the setup is completed, press MENU to exit the menu screen. Note Make this setup for each input (INPUT1 and INPUT2). SELECT SET ENTER MENU EXIT 14 En Setting Up the System CLAMP POSITION setup Depending on the signal, analog RGB signals may result in the screen image appearing with a whitish or greenish cast. ÷ Normally, leave this setting at AUTO. Press SET to select LOCKED. MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L A MP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : L O CK E D : V GA Setup of CLAMP POSITION 1 Press MENU to display the menu screen. The menu screen appears. MAIN MENU SCREEN : CO NT RA S T 0 : BR I GHT . [. . . ] AC 100 - 120 V, 50/60 Hz Rated current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 8 A - 3. 1A Standby power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 oz) Audio Input AUDIO INPUT (for INPUT 1/2) Stereo mini jack L/R . . . 500mVrms/more than 10 k Output AUDIO OUTPUT Stereo mini jack L/R . . . [. . . ]