User manual HITACHI CJ18DL

[. . . ] CJ18DL Read through carefully and understand these instructions before use. English 1 2 3 4 5 6 7 8 9 0 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ \ Rechargeable battery Latch Handle Pull out Insert Lever Blade Blade holder Roller Lock off button Lock Free Switch Change knob Splinter guard Base Insert Chip cover Insert Open Base bolt Hexagonal bar wrench Forward Guide Attachment hole M5 bolt Nail or screw Guide hole Scale Semi-circular part -mark Cleaner Dust collector Adapter Nose Rear hole Hook Notch D) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. This enables better control of the power tool in unexpected situations. [. . . ] If you find rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the first time, do not use and return it to your supplier or vendor. "x" Indicates that the battery pack is not compatible with that specific charger. (2) Guide (3) Sub base (4) Dust collector Optional accessories are subject to change without notice. Cutting various lumber and pocket cutting Cutting mild steel plate, aluminum plate, and copper plate Cutting synthetic resins, such as phenol resin and vinyl chloride Cutting thin and soft construction materials Cutting stainless steel plate (with No. Insert the battery into the charger Insert the battery firmly, until it contacts the bottom of the charger compartment. CAUTION If the battery is inserted in the reverse direction, not only recharging will become impossible, but it may also cause problems in the charger such as deformed recharging terminal. (1) Pilot lamp indication The indications of the pilot lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery. Battery installation Insert the battery while observing its polarities (See Fig. UC18YRL Before using the cordless jig saw, charge the battery as follows. Connect the charger's power cord to a receptacle When the power cord is connected, the charger's pilot lamp will blink in red (At 1-second intervals). (2) Regarding the temperatures of the rechargeable battery The temperatures for rechargeable batteries are as shown in the table below, and batteries that have become hot should be cooled for a while before being recharged. Table 2 Recharging ranges of batteries Charger UC18YRL Rechargeable batteries Ni-Cd batteries Li-ion batteries ­5°C ­ 55°C 0°C ­ 50°C CAUTION If the battery is charged while it is heated because it has been left for a long time in a location subject to direct sunlight or because the battery has just been used, the pilot lamp of the charger lights up green. 2second intervals), check for and take out any foreign objects in the charger's battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Since the built-in micro computer takes about 3 seconds to confirm that the battery being charged with UC18YRL is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged. UC18YG Before using the cordless jig saw, charge the battery as follows. Hold the charger firmly and pull out the battery NOTE Be sure to pull out the battery from the charger after use, and then keep it. Connect the charger power cord to the receptacle Connecting the power cord will turn on the charger. Insert the battery into the charger Insert the battery firmly while observing its direction, until it contacts the bottom of the charger (the pilot lamp lights up). CAUTION If the pilot lamp does not light up, pull out the power cord from the receptacle and check the battery mounting condition. the pilot lamp goes off to indicate that the battery is fully charged. [. . . ] When the speed is too low, cutting will take longer, although the service life will be prolonged. The blade number is engraved in the vicinity of the mounting portion of each blade. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a Hitachi Authorized Service Center. [. . . ]