User manual HITACHI CDS225W

[. . . ] Liquid Crystal Projector Thank you for purchasing this liquid crystal projector. WARNING · Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. [. . . ] Select an item with the and buttons, and start operation. SETUP AUTO RGB VIDEO HDTV INPUT IMAGE EXECUTE CANCEL OPT. Table 5. Input Menu Item Description Operation Start/Stop: Press the / button. Automatic Adjustment at RGB Input: Select the EXECUTE with the button. Horizontal position (H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE), and horizontal size (H. SIZE) are automatically adjusted. Use with the window at maximum size in the application display. · This operation requires approximately 10 seconds. · This function is the same as for the AUTO function in Basic operation. AUTO RGB Displays RGB Input Frequency: Displays the horizontal and vertical sync signal frequencies for RGB input. · Valid only at RGB input. VIDEO Operation Start/Stop: Press the / button. Select Video Signal Type: Select the signal type with the and buttons. Select NTSC, PAL, SECAM, NTSC4. 43, M-PAL, or N-PAL as appropriate for the input signal. The selection of AUTO enables and executes the function AUTO (Automatic Adjustment at Video Input), except for the N-PAL input. · Use this function when the image becomes unstable (eg. Pressing the AUTO button in this case may correct this problem except for the N-PAL input. · For the COMPONENT VIDEO input, this function is not effective and the signal type is distinguished automatically. HDTV Operation Start/Stop: Press the / button. Select HDTV Mode: Select the 1080i mode or 1035i mode suitable for the input signal with the / button. · When the selected HDTV mode is incompatible with the input signal, the image may be incorrect (eg. the display position or color is incorrect). ENGLISH-12 OPERATIONS (continued) SETUP INPUT IMAGE OPT. The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start operation. BLANK MIRROR START UP GAMMA COLOR TEMP Table 6. Image Menu Item BLANK MIRROR Description Select Blank Screen Color: Select color with the and buttons. · The image is cleared when the BLANK mode is set with BLANK ON, or when there is no signal, and the entire screen is displayed in the selected color. START UP Operation Start/Stop: Press the / button. Clear Initial Screen Display: Select TURN OFF with the button. · Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal. GAMMA COLOR TEMP Operation Start/Stop: Press the / button. Select Gamma Mode : Select the gamma mode with the / button. Operation Start/Stop: Press the / button. Select Color Temperature: Select the color temperature mode with the / button. ENGLISH-13 ENGLISH Image Menu OPERATIONS (continued) Options Menu The following adjustments and settings are available when OPT. Options Menu Item VOLUME MENU COLOR LANGUAGE Description Volume Adjustment: Reduce VOLUME Increase VOLUME Select Menu Background Color: Select with the Operation Start/Stop: Press the or button. The system automatically enters the standby mode when a signal is not received for the set time. When STOP is selected the system does not enter the standby mode even if no signal is received. SYNC ON G Invalid: Select TURN OFF with the button. · May not be displayed correctly with some input signals when SYNC ON G is valid. [. . . ] NO INPUT IS DETECTED ON *** SYNC IS OUT OF RANGE ON *** CHECK THE AIR FLOW NOTE *1) This message is cleared automatically after approximately three minutes, and appears every time power is switched ON. ENGLISH-19 ENGLISH OSD Message TROUBLESHOOTING (continued) Indicators Message The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Indicators Message POWER LAMP TEMP indicator indicator indicator Lights orange Blinks green Lights green Blinks orange Blinks red Contents Turns off Turns off The Standby mode has been set. Take the appropriate measures when the POWER indicator ceases blinking Lamp is not lit. Switch power OFF, wait 20 minutes until the equipment cools, and check whether the Turns off ventilation openings are blocked, whether the air filter is dirty, or whether the ambient temperature exceeds 35 °C. [. . . ]