User manual HITACHI CDR-8430 32X

[. . . ] All rights reserved Publication Number: 32x CD-ROM Manual - Page 2 For USA Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC RULES. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] If you do not: · When the Disc Tray is opened, the disc may jump out and may be damaged. · Your CD-ROM Drive may not work with full performance. 5û 5û 5û 5û 32x CD-ROM Manual - Page 6 · Mounting screw The screws must be ISO (M3X0. 5) to mount the CD-ROM Drive tightly and avoid damaging the mechanism inside the CD-ROM Drive. (See page 10) · Moving your CD-ROM Drive Remove the disc and close the Disc Tray before moving the CD-ROM Drive. If your CD-ROM Drive is moved with the disc loaded or the Disc Tray opened, both the disc and the CD-ROM Drive may be damaged. Precautions For Care · Cleaning of the CD-ROM Drive, discs · Never clean your CD-ROM Drive and discs with silicon cloths or cloths soaked in water, solvents (thinner, benzine), abrasive cleaner, anti-static sprays, any record cleaner sprays, liquid cleaner or aerosol cleaner. It may damage or discolor the coating of the CD-ROM Drive or damage or deform discs. · Clean your CD-ROM Drive including the Disc Tray and discs with a clean, dry, soft cloth at least once a month. · Cleaning needed warning If you begin to get error messsages that your drive is unable to read a disc, it may mean that cleaning is needed. Clean your CD-ROM drive's pick-up lens using a cleaning disc. 32x CD-ROM Manual - Page 7 Controls and Functions 2 6 Front Panel Rear Panel 34 1 5 78 9 10 1) LOADING/UNLOADING/BUSY INDICATOR Indicator blinks green only when the Disc Tray is being opened or closed, or when the CD-ROM drive is accessing data. 2) DISC TRAY When the power of the CD-ROM Drive is turned off, the Disc Tray cannot be opened and closed. 3) HEADPHONE JACK ( 3. 5 mm) 4) HEADPHONE VOLUME CONTROL Adjust the headphone volume. 5) OPEN/CLOSE BUTTON Press this button to open or close the Disc Tray. If the Disc Tray does not open when the OPEN/CLOSE Button is pressed, the CD-ROM Drive's Manual Emergency Eject mechanism may be activated. (See page 12 about Manual Emergency Eject Procedure) 7) AUDIO OUTPUT TERMINAL Circuit Board Rch GND Lch 32x CD-ROM Manual - Page 8 8) DEVICE CONFIGURATION JUMPER This Connector is used to set operation modes such as Master, Slave and CSEL 642 Device is Master 531 or (default setting) Device is Slave Cable Select 9) ATAPI INTERFACE CONNECTOR ATAPI bus connection (40 pin) 10) POWER SUPPLY CONNECTOR (DC Input) For connecting the power supply cable. Circuit Board +5V GND +12V Installation Requirements HARDWARE · · · · · CD-ROM Drive Interface card Interface cable Power supply cable Mounting screws 32x CD-ROM Manual - Page 9 HARDWARE OPTION · Audio connecting cable · Sound Card SOFTWARE · CD-ROM device driver NOTE: If you need a interface card or interface cable or CD-ROM device driver, contact your dealer. Hardware Installation To install this CD-ROM drive in the host computer, refer to the instruction manual of each host computer. And to install the interface card in the host computer, refer to the instruction manual of each host computer and each interface card. Install the CD-ROM Drive following general installation procedure shown below. 1) Check the Device Configuration Jumper settings of the CD-ROM Drive such as Master, Slave, CSEL. (See page 9) 2) Turn off the host computer and unplug the power supply cable of the host computer. 4) Install the CD-ROM Drive into the host computer and mount tightly by screws. 7) Firmly attach the interface cable from the interface card to the CD-ROM Drive. 9) Finally attach a spare DC power supply cable from the computer power supply to the CD-ROM Drive firmly. [. . . ] (by AUDIO SOURCE in U. S. A. , by AKUSTIK SISTEME VERTRIEBS GHBH in GERMANY and by SAEC COMMERCE CO. , LTD. 2) Using the small brush supplied with the cleaning disc case, straighten up the disc cleaning brushes on the back of the cleaning disc. 3) Place the cleaning disc in the Disc Tray with its arrow marked on the disc at front. 4) Press the OPEN/CLOSE button or push the center of the Disc Tray lightly and close the Disc Tray. [. . . ]