User manual HITACHI AX-M131U

[. . . ] HI-FI COMPONENT SYSTEM AX-M131U Operating Instructions Table of Contents Important Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The service database during the scan operation shall be updates and the preset be cleared. If Cancel button is pressed during scan, the scan shall be aborted and go back to the previous frequency before scan. During scanning, the receiver shall initially display the following, where "CH" is the DAB channel and "N" is the number of ensemble currently detected. CH N -8- 5. When the scan is complete, a tune operation to the first service of the first ensemble in the ensemble list shall be preformed. If the service database is still empty after a scan, the receiver shall display the following: NO SIGNAL Manual tune 1. The receiver shall display the following for 2 seconds: MANUAL TUN After this time, the receiver shall display the current DAB channel and frequency 12B 225 648 If the up or down buttons are pressed, the receiver shall step forwards or backwards through the full range of channels. If the select button is pressed, the first service for the current ensemble shall be selected, the receiver shall return to this idle state. If the info button is pressed, the information text displayed during the idle process shall step through each of the following: 2. DLS-this shall scroll from right to left at approximately 4 characters per second. Scroll DLS Where no DLS information is available, the receiver shall display the following: NO DLS 3. Programme type, if the Programme type is less than 10, it shall display the following, if the Programme type is larger than 10, it shall scroll from right to left at approximately 4 characters per second. Program Type if no PTY is available, the receiver shall display the following: NO PTY 4. Time and Date (month day hour minute) shall display the following: MM-DD HH:MM 7. Audio type and bit rate ­ the audio type (Stereo, Mono) shall be right justified, and the bit rate shall be left justified. If the Cancel button is pressed, the information text shall revert to Service name. When a program button is pressed, it will display the following: PN Where "N" is the preset number, press Program again or press number key, and the current service will be saved to the preset. Then it will display the following for 2 seconds. PN SAVED When a number button is pressed, if there is a service associated with the preset, a tune operation to the service shall be performed. If there is no service associated with the preset, the receiver shall display the following( where "N" is the preset number) for 2 seconds: PN EMPTY FM Radio You can listen to FM stations. Stations can be tuned in manually, automatically, or from preset memory storage. Caution: Before listening to the radio, please check that both the FM antennas are correctly connected and adjusted for length and direction. Repeatedly press the function button (FUNCTION) on the front of the unit or press the tuner function button (TUNER) on the remote control (under the number buttons). Press the tuner function button (TUNER) on the remote control to select the band or the band button on the top of the unit. Manual Tuning Press the tuning backward button (TU-) or tuning forward button (TU+) repeatedly to change the frequency until you find the station you want. Auto Tuning If you press and hold the tuning backward button (TU-) or tuning forward button (TU+) on the unit or remote control for one second or more, the frequency changes down, or up, automatically until a station is found. [. . . ] Turning off the system also cancels the sleep timer. Setting the Daily on Timer You can use the setting timer to make the unit automatically turn on at a certain time everyday from standby. When the setting timer is on, the timer indicator " " will be displayed. But the clock must be correctly set for the timer to operate correctly. In standby mode, press the timer button (TIMER) on the remote control twice, the hour indicator will blink. [. . . ]