User manual HITACHI 70VX915

[. . . ] LCD REAR PROJECTION TELEVISION Operating Guide for 50VX915, 60VX915, 70VX915 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 FIRST TIME USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 THE REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-49 ON-SCREEN DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The last Freeze mode you selected before you pressed the EXIT button will be the one that comes up after pressing the PAUSE button again. Strobe Freeze is not available in 480p/720p/1080i inputs. 41 USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. You must first program the remote to match the remote system of your cable box (refer to pages 48-49 for pre-codes). To switch to Cable (CBL) pre-coded mode, use the SOURCE ACCESS buttons ( light to the corresponding selection. , ) on the remote control to position the LED 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your cable box as shown on pages 4849. The remote will turn off your cable box when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different four digit preset code. The remote will now control your Cable box. 5. 6. THE REMOTE CONTROL NOTES: 1. If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. GUIDE A/V NET 3. PRECODED CABLE BOX buttons These buttons transmit the chosen precoded cable codes. EXCLUSIVE TV buttons These buttons are for operating the TV. MY CABLE BOX CODE IS: NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box. 42 USING THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS Operating the precoded function for your set-top-box/satellite receiver. This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems (refer to pages 48-49 for pre-codes). Aim the remote control at the front of your set-top-box/satellite systems. To switch to set-top-box/satellite (STB) pre-coded mode, use the SOURCE ACCESS buttons ( tion the LED light to the corresponding selection. , ) on the remote control to posi- 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your set-top-box/satellite receiver as shown on page 48-49. Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your settop-box/satellite receiver. [. . . ] Its component parts may not be separated for use on more than one DTV. You may not transfer, assign, rent, lease, lend or in any way sublicense the Software. This License Agreement does not grant you any rights to any trademarks. You shall not use the Software in combination with any third party software. [. . . ]