User manual HITACHI 60VG825

[. . . ] LCD REAR PROJECTION TELEVISION Operating Guide for 50VG825, 55VG825, 60VG825 IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 FIRST TIME USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 THE REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-38 ON-SCREEN DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] CHANNEL (CH) WHEEL/CHANNEL SELECTOR buttons The CHANNEL wheel or the CHANNEL SELECTOR buttons are used to select channels, lock access code, etc. Use the CHANNEL SELECTOR buttons to enter one, two, or three numbers to select channels. Enter "0" first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For Digital Channels, use the CHANNEL SELECTOR buttons with the (-) DASH button. Channel selection may also be performed by CHANNEL WHEEL up ( ) or CHANNEL WHEEL down ( ). (-) DASH button Use the (-) DASH button with the CHANNEL SELECTOR buttons to enter Digital Channels that have subchannel numbers indicated by (-) DASH (example 15-1). BACKLIGHT button Press this button to light up and illuminate the buttons of the remote control. 27 Picture-In-Picture (PIP) Your HITACHI LCD Rear PTV incorporates Two Tuner technology designed for improved viewing enjoyment. This Two Tuner feature allows you to view antenna inputs on both the main picture and sub picture simultaneously, with separate tuning control for each. When a Digital channel is viewed in the main picture, the Digital channel can not be viewed in the sub picture. And when the Analog channel input is viewed in the main picture, the Analog channel input can not be viewed in the sub picture. To select between main picture and PIP sub picture tuning, use the CURSOR PAD button on the remote. The Green highlighted channel display will move with every press of the CURSOR PAD buttons. Apparatus Claims of U. S. 4, 631, 603; 4, 577, 216; 4, 819, 098; 4, 907, 093; and 6, 381, 747 licensed for limited viewing uses only. CableCARDTM (Top of card faces right) CABLE Top faces Connect the Cable and/or Air cables Upgrade Card HDMI INPUT 1 AIR MONITOR OUT S I V I D E O V I D E O A U D I O Y/ VIDEO Y/ VIDEO HDMI INPUT 2 PB PB OPTICAL OUT PR PR Digital Audio (MONO) (MONO) (MONO) (MONO) / G-LINK L TV AS CENTER R CAUTION The Remote Control The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing other programs from any of the video inputs. Use the connection diagram to the right to view VCR program (from Input 1-5) as a sub-picture while viewing another program as main picture (CABLE, AIR). You may also view the VCR program (from Input 1-5) as a main picture while viewing another program as a subpicture (CABLE or AIR). When installing a CableCARD, connect your coaxial cable to CABLE (see page 12). PIP button Press the PIP button and a sub-picture will appear in one of the four different modes (POP, PIP, SPLIT or SURF), depending on the INPUT signal. To change the PIP mode, use the PIP button to cycle through the four different modes. POP MODE PICTURE-IN-PICTURE POP Mode PIP displays the sub-picture outside of the main picture. Please refer to the PICTURE-IN-PICTURE MODES Table (see page 29). AUDIO TO HI-FI INPUT 1 INPUT 2 INPUT 3 INPUT 4 Audio Video OUTPUT VCR Main Picture Sub Picture NOTES: 1. Only one INPUT (1-5) and one antenna (Cable or Air). 28 Picture-in-Picture (PIP) PIP MODE PICTURE-IN-PICTURE Select AIR from the INPUTS menu. To prevent a pattern burn, occasionally move the sub-picture using the CURSOR PAD. [. . . ] The channel information that can be edited includes: · · · Change the position order channels appear in the LISTINGS Service screen. Change a channel to one of the following settings: - ON (Channel is displayed in LISTINGS) - OFF (Channel is not displayed in LISTINGS) - AUTO-HIDE (Channel is displayed in LISTINGS only when program information is available Change the service type for the source: - Cable - Cable Box - Over-the-Air - Antenna - Etc. NOTE: The Tune channel is the channel on which the TV receives a station depending on its type of cable, cable box, or antenna services. · 62 TV Guide On Screen CHANGE DEFAULT OPTIONS: Use this option to change default settings: · General Defaults · Record Defaults · Remind Defaults · IR Defaults GENERAL DEFAULT OPTIONS 1. From the SETUP screen, use the CURSOR PAD or to highlight Change Default Options and then press the SELECT button RECORD DEFAULTS 1. From the SETUP screen, use the CURSOR PAD or to highlight Change Default Options and then press the SELECT button. [. . . ]