User manual HITACHI 57XWX20B

[. . . ] PROJECTION COLOR TV 65XWX20B 57XWX20B 51XWX20B OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS 2-3 FIRST TIME USE 4-23 THE REMOTE CONTROL 24-42 Video Audio Ch. Manager Locks Setup Move SEL ON-SCREEN DISPLAY 43-71 Sel USEFUL INFORMATION INDEX 72-79 IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television. [. . . ] Hold down the VCR button on the remote and enter the two digit preset code that matches your VCR, as shown on page 42. The remote will turn off your VCR when the correct two digit preset code is entered. The remote will now control your VCR. POWER 5. 6. TV VCR CBL STB SOURCE WIZARD DVD CD TAPE AMP NOTES: 1. If your VCR cannot be operated after performing the above procedures, your VCR's code has not been precoded into the remote. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. VCR Button This button allows the remote to control your VCR by setting it to VCR mode. PRECODED VCR Buttons These buttons transmit the chosen precoded VCR codes. For some VCRs, you must press the RECORD button twice to record a program. EXCLUSIVE TV Buttons These buttons are for operating the TV. 1 4 7 SLEEP 2 5 8 0 3 6 9 INFO ANT A/V NE T GUIDE ASPECT VIRTU AL H D ME NU EX IT VOL SELECT CH SV CS MUT E CH LAST SC HD 5 VID 1 VID VID 2 VID 3 VID 4 PIP PIP CH FREEZE PIP MODE PIP ACCESS SWAP VIDEO REC CLU-5721TSI MY VCR CODE IS: NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR. 36 USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. You must first program the remote to match the remote system of your cable box. Press and release the Cable (CBL) button to switch to Cable pre-coded mode. Hold down the CBL button on the remote and enter the two digit preset code that matches your cable box as shown on page 42. The remote will turn off your cable box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different two digit preset code. The remote will now control your Cable box. TV POWER 5. 6. NOTES: 1. If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. [. . . ] This is usually caused by interference from automobile ignition systems, neon lamps, electrical drills, ghosting of the image and weak signals. · BLACK SCREEN (ANT C Input): When using an antenna, weak signals will display a black screen. It may be necessary to upgrade your antenna. NOTE: The TV set can generate sound distortion in external devices such as a radio. Please separate radio equipment from the TV set to a considerable distance. 73 USEFUL INFO SYMPTOMS No Picture, no sound © Sound OK, picture poor © Picture OK, sound poor © Picture blurred © Lines or streaks in picture Poor reception on some channels Picture rolls vertically No color © Poor color © ©© HITACHI Projection Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges. IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1. [. . . ]