User manual HITACHI 51SWX20B

[. . . ] PROJECTION COLOR TV 65SWX20B 57SWX20B 51SWX20B 65TWX20B 57TWX20B OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS 2-3 FIRST TIME USE 4-20 THE REMOTE CONTROL 21-37 Video Audio Ch. Manager Locks Setup Move SEL ON-SCREEN DISPLAY 38-62 Sel USEFUL INFORMATION INDEX 63-68 As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. [. . . ] In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. VCR Button This button allows the remote to control your VCR by setting it to VCR mode. PRECODED VCR Buttons These buttons transmit the chosen precoded VCR codes. For some VCRs, you must press the RECORD button twice to record a program. EXCLUSIVE TV Buttons These buttons are for operating the TV. 1 4 7 2 5 8 0 3 6 9 SLEEP INFO ANT C. C. A/V NET ASPECT VIRTU AL HD ME NU EX IT VOL SELECT CH SV CS MUT E VCR PLUS + CH LAST GUIDE/T V SC HD 5 VID 1 VID VID 2 VID 3 VID 4 PIP PIP CH FREEZE PIP MODE PIP ACCESS SWAP VIDEO REC CLU-5722TSI MY VCR CODE IS: NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR. 31 USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. You must first program the remote to match the remote system of your cable box. Press and release the Cable (CBL) button to switch to Cable pre-coded mode. Hold down the CBL button on the remote and enter the two digit preset code that matches your cable box as shown on page 37. The remote will turn off your cable box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different two digit preset code. The remote will now control your Cable box. TV POWER 5. 6. NOTES: 1. If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. The LAST CH button will act as the cable box ENTER button if required. VCR CBL STB SOURCE WIZARD CD DVD TAPE AMP 1 4 7 2 5 8 0 3 6 9 SLEEP INFO ANT C. C. A/V NET ASPECT VIRT UAL HD 3. NU ME EX IT VOL SELECT CH 4. SV CS MU T E VCR PLUS + CH LAST GUIDE/ TV SC HD 5 VID 1 VID VID 5. The SLEEP button will act as your cable box `100' button if required. CABLE (CBL) button This button allows the remote to control your cable box by setting it to CABLE mode. PRECODED CABLE BOX buttons These buttons transmit the chosen precoded cable codes. EXCLUSIVE TV buttons These buttons are for operating the TV. 2 VID 3 VID 4 PIP PIP CH FREEZE PIP MODE PIP ACCESS SWAP VIDEO 6. REC CLU-5722TSI MY CABLE BOX CODE IS: NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box. 32 USING THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS Operating the precoded function for your set-top-box/satellite receiver. [. . . ] Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. · SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. · RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. NOTE: The TV set can generate sound distortion in external devices such as a radio. Please separate radio equipment from the TV set to a considerable distance. 64 USEFUL INFO SYMPTOMS No Picture, no sound © Sound OK, picture poor © Picture OK, sound poor © Picture blurred © Lines or streaks in picture Poor reception on some channels Picture rolls vertically No color © Poor color © ©© HITACHI Projection Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges. [. . . ]