User manual HITACHI 50UX23K

[. . . ] IMPORTANT -1- PROJECTION COLOR TV 60SX10B/11K, 50SX7P, 50UX22B/23K, 46UX20B/21K OPERATING GUIDE TABLE OF CONTENTS IMPORTANT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY TIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PICTURE CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (See pages 15 and 42. ) ARTIFICIAL INTELLIGENCE (AI) button Press this button to turn the AI function on or off. (See page 38) PICTURE-IN-PICTURE (PIP) The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing a VCR program (TV or tape) on any of the video inputs. PIP BUTTON PICTURE-IN-PICTURE (PIP) - 24 - Press the "PIP" button and a sub-picture appears in one corner of the screen. Press the button a second time to remove the sub-picture from the screen. Press the AVX button when the sub-picture is on to change between VIDEO: 1, VIDEO: 2 and VIDEO: 3. The TV channel will always be either the main picture or the sub-picture. SWAP BUTTON If you wish to switch what is being shown on the main picture to the sub-picture, press the "SWAP" button. SHIFT BUTTON To move the sub-picture to another corner, press the "SHIFT" button. The sub-picture moves one step counter-clockwise every time the "SHIFT" button is pressed. FREEZE (FRZ) BUTTON If you wish to freeze the sub-picture, press the "FRZ" button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the button again. STROBE FREEZE Press this button without a sub-picture to freeze one or four frames of the picture you are currently viewing. The four frame strobe freeze is useful for viewing a moving picture that has many details, for example, a close play in a sporting event or a golf swing. USING THE REMOTE TO CONTROL VCR FUNCTIONS - 25 - CAUTION: A pattern burn may develop if the sub-picture is left in the same corner permanently. If the PIP feature is used frequently, occasionally shift the sub-picture to a different corner. NOTE: 1. Only sound from the main picture can be heard, unless you choose PIP from wireless mode and use the "TRANSMITTER OUT" outputs on the rear panel. Each strobe freeze frame is delayed about 0. 3 (3/10) second. USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the pre-coded function for your VCR This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system in your VCR. While holding down the VCR POWER button on the remote, enter the 2 digit preset code that matches your VCR as shown on page 26. The remote will turn off your VCR when the correct 2 digit preset code is entered. If the VCR does not turn off after 5 seconds, try a different 2 digit preset code. If your VCR cannot be operated after performing the above procedures, this means that your VCR's codes have not been precoded into the remote. In the unlikely event that your VCR cannot be operated after performing the above USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS - 26 - procedures, please consult your VCR operating guide. The remote control will remember the codes you have programmed in until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure stated above. If your VCR does not have a power function, the remote will issue the CHANNEL UP function. PRECODED VCR BUTTONS These buttons transmit the chosen precoded VCR codes. EXCLUSIVE TV BUTTONS These buttons are for operating the TV. [. . . ] Labor charges to repair or replace lenses found to be defective after the one year warranty duration will not be covered. Any new product purchased or service performed outside of the continental United States or its possessions. Uncrating, setup, installation, or adjustments of customer operated controls. Repairs or replacement parts supplied by other than an Authorized Hitachi Service Facility. [. . . ]