User manual HITACHI 43F300

[. . . ] PROJECTION COLOR TV 43F300 53F300 OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS 2-3 FIRST TIME USE 4-18 THE REMOTE CONTROL 19-29 Video Audio Ch. Manager Locks Setup Move SEL ON-SCREEN DISPLAY 30-56 Sel USEFUL INFORMATION INDEX 57-63 As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. [. . . ] The remote will now control your cable/satellite box. POWER TV CBL/SAT DVD/VCR 6. NOTES: 1. If your cable/satellite box cannot be operated after performing the above procedures, your cable/satellite box code has not been precoded into the remote. In the unlikely event that your cable/satellite box cannot be operated after performing the above procedures, please consult your cable/satellite box operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. PIP VIDEO SWAP PIP MODE PIP CH FREEZE MENU SELECT THE REMOTE CONTROL 3. MUTE EXIT LAST CH VOL CH CABLE (CBL/SAT) button This button allows the remote to control your cable/satellite box by setting it to CABLE/SATELLITE mode. PRECODED CABLE/SATELLITE BOX buttons These buttons transmit the chosen precoded cable/satellite codes. EXCLUSIVE TV buttons These buttons are for operating the TV. 1 4 7 ANT 2 5 8 0 VID3 3 6 9 INFO VID1 VID2 VID4 REC VID5 ASPECT VIRTUAL HD CABLE BRAND CODE SATELLITE BRAND CODE 32 29 33 34 35 36 31 General Instrument . . MY CABLE/SATELLITE BOX CODE IS: NOTE: Refer to instruction manual of the Cable/Satellite Box for operation of the buttons exclusively for the Cable/Satellite Box. 28 USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. You must first program the remote to match the remote system of your DVD player (refer to table below for pre-codes). Hold down the DVD/VCR button on the remote and enter the two digit preset code that matches your DVD player, as shown below. The remote will turn off your DVD player when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different two digit preset code. The remote will now control your DVD player. POWER 6. NOTES: 1. If your DVD player cannot be operated after performing the above procedures, your DVD player's code has not been precoded into the remote. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. TV CBL/SAT DVD/VCR PIP VIDEO SWAP PIP MODE PIP CH FREEZE MENU SELECT THE REMOTE CONTROL MUTE EXIT LAST CH DVD/VCR Button This button allows the remote to control your DVD player by setting it to DVD mode. PRECODED DVD Buttons These buttons transmit the chosen precoded DVD codes. EXCLUSIVE TV Buttons These buttons are for operating the TV. VOL CH 1 4 7 ANT 2 5 8 0 VID3 3 6 9 INFO VID1 VID2 VID4 REC VID5 ASPECT VIRTUAL HD DVD BRAND CODE 60 55 56 57 59 60 54 58 Hitachi . . MY DVD PLAYER CODE IS: NOTE: Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player. 29 ON-SCREEN DISPLAY (OSD) 1. Press MENU on the remote control to display the different features on your HITACHI Projection TV. [. . . ] One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. · SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. · RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. NOTE: The TV set can generate sound distortion in external devices such as a radio. [. . . ]