User manual HITACHI 32HDL51

[. . . ] LCD TELEVISION AVC (Audio Video Control Center) & LCD Display Monitor Operating Guide for 32HDL51 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 FIRST TIME USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 THE REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-49 ON-SCREEN DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. GUIDE A/V NET 3. PRECODED CABLE BOX buttons These buttons transmit the chosen precoded cable codes. EXCLUSIVE TV buttons These buttons are for operating the TV. MY CABLE BOX CODE IS: NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box. 42 HOW TO USE THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS Operating the precoded function for your set-top-box/satellite receiver. This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems (refer to pages 48-49 for pre-codes). Aim the remote control at the front of your set-top-box/satellite systems. To switch to set-top-box/satellite (STB) pre-coded mode, use the SOURCE ACCESS buttons ( position the LED light to the corresponding selection. , ) on the remote control to 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your set-top-box/satellite receiver as shown on page 48-49. Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your set-topbox/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different four digit preset code. The remote will now control your set-top-box/satellite receiver. 5. 6. NOTES: 1. If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-topbox/satellite receiver code has not been precoded into the remote. In the unlikely event that your set-top-box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. PRE-CODED SET-TOP-BOX/SATELLITE RECEIVER buttons These buttons transmit the chosen pre-coded set-topbox/satellite codes. EXCLUSIVE TV buttons These buttons are for operating the TV. THE REMOTE CONTROL A/V NET 3. GUIDE MY SATELLITE RECEIVER/STB CODE IS: NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-topbox/satellite receiver. 43 HOW TO USE THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. You must first program the remote to match the remote system of your DVD player (refer to pages 48-49 for pre-codes). [. . . ] Its component parts may not be separated for use on more than one DTV. You may not transfer, assign, rent, lease, lend or in any way sublicense the Software. This License Agreement does not grant you any rights to any trademarks. You shall not use the Software in combination with any third party software. [. . . ]